2014 Toyota Prius Three 4dr Hatchback on 2040-cars

Auto blog

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Toyota GT86, Scion FR-S sales disappointing worldwide?

Okay, folks - it appears we've got a problem. The Toyota GT86, Europe's counterpart to our own beloved Subaru BRZ and Scion FR-S coupes, is apparently not selling too well. This, according to Toyota's European Vice President of Research and Development, Gerald Killman, is what's limiting plans for additional variants of the rear-drive coupe.
"A faster version of that car would be at the top of most people's wish lists, but like the cabriolet, it is hard to justify a business case to push either model into production based on the current sales," Killman told AutoExpress. "Personally, I think that engine could use a little bit more," he added.
More troubling is that slow sales aren't limited to the Euro-spec car, with Killman claiming that the GT86 have been missing sales targets in major markets around the globe. It may not be that the US is one of those major markets, though. Scion's Vice President, Doug Murtha, tells Autoblog that his brand is happy with the sales of its version of the GT86, the FR-S. 18,000 units were sold last year, which Murtha says is "generally in line with original expectations for the car."

Toyota TRD Pro Chase Trucks are ready to hit the desert at SEMA

Toyota marks the 35th anniversary of its Toyota Racing Development performance arm this year, and the division is celebrating at this year's SEMA Show with a quartet of tuned off-roaders based on on the 4Runner, Tacoma and Tundra that look more than ready to go just about anywhere.
All four of them will take part in this year's Baja 1000 race, but only the Tundra (far left in the above photo) is actually competing. The other three will be there to act as support vehicles.
Inspired by the production TRD Pro Series trucks, the 4Runner, Tacoma and Tundra are prepared by off-road fabricator N-Fab with a mix of TRD and the company's own parts to be able to take whatever the grueling, 1,000-mile can throw at them. The trio is fettled with extra communications equipment, GPS, additional lights and all sorts of body and suspension modifications to help them survive the ordeal.