Toyota Bj42 Land Cruiser Diesel 1983 Lhd on 2040-cars

Auto blog

2016 Mazda MX-5 Miata battles Toyota GT86 on track

It's got two doors and a 2.0-liter four-cylinder engine up front, driving the rear wheels. It's made in Japan, and as far as bang-for-your-buck goes, it's a downright bargain. So which are we talking about, the Mazda MX-5 Miata, or the Toyobaru coupe known alternately as the Subaru BRZ, Scion FR-S, or Toyota GT-86? The answer is "yes," and it just goes to show, roofs notwithstanding, how close these two vehicles really are to one another. Which one is your favorite may come down to a matter of personal taste, but for its latest video, Auto Express set out to find out which laps faster around the track. On paper at least, the Toyota's 200 horsepower will trump the Mazda's 155 any day of the week, and twice on Sunday. Then again, the Miata does weigh a good 400 pounds less, even with the 2.0-liter engine and despite its convertible bodystyle – but is that enough to make up the difference? You're going to have to just watch the video for yourself to find out. All we'll tell you is that the match is pretty darn close – what you might call a photo finish, if they were actually racing each other at the same time as opposed to each racing the clock separately. So watch the video above and voice your support for your favorite little Japanese sports car in the Comments section. Related Video:

Honda, Nissan and Mazda recalling 3 million vehicles for airbag inflators

Three million more vehicles can be added to the worldwide tally to be repaired for the faulty airbag inflators supplied by Takata. Honda, Nissan, and Mazda have all issued recalls to replace the bad part, including about 1.2 million of them in North America. NHTSA has been investigating all three companies, plus Chrysler and Toyota, for potentially affected vehicles.
Honda is recalling roughly 1.02 million Civic, CR-V, Odyssey and Element models In North America, built between April 2000 and October 2002. Mazda needs to repair 14,794 units of the RX-8 and Mazda6, and Nissan has 228,000 vehicles in North America to be fixed.
Chrysler is also starting what it calls a "regional field action" to replace the inflators in the 2006 Dodge Charger, according to a company spokesperson. The company says that it has not yet found the problem in any of its vehicles, but it's being done "out of an abundance of caution." The final number of Chargers affected will be announced later this week.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.