2001 Toyota Avalon, No Reserve on 2040-cars

Auto blog

Lexus planning a hydrogen fuel-cell LS by 2017

Toyota's Fuel Cell System will certainly migrate to other vehicles in the carmaker's lineup, but Australian car site Motoring reports that one of the models at the head of the queue is the Lexus LS. According to its sources, the executive barge powered by hydrogen will be released by 2017 and take the top spot in the range, rolling in above the LS Hybrid. We're told that Toyota engineers will find a way to slide two hydrogen tanks into its bodywork with the same general setup as on the Mirai – one under the rear seats and another under the rear parcel shelf. The 150-kW fuel cell stack will be placed under the front seats. Motoring says the resulting sedan and its 220-kW electric motor would come in "at around 2,100 kg," which is 4,620 pounds; that's a ginormous 539 pounds less than the listed curb weight of the current LS Hybrid, and 387 pounds more than the standard LS. Assuming all goes as planned, it would have a range of roughly 238 miles, a few dozens less than the Mirai's range of about 300 miles. It would look slightly different, too, the front end getting larger intakes to cool the power unit. It wouldn't surprise us if Lexus does have a hydrogen LS planned – it would be a statement car, and the company likes making statements, even if few heed them; it has stuck with its LS 600h for the past seven years, yet of the 7,539 LS models sold through the end of November this year, only 61 of them were hybrids. The timing would be intriguing, however; by the time the LS hybrid came out, Lexus had already worked over its filet-and-potatoes models. And if the hydrogen version is going to come in above the $120,440 hybrid, well, that will be a statement indeed.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Toyota FCV puts hydrogen fuel cell twist on ALS Ice Bucket Challenge

You've probably seen your fair share of Ice Bucket Challenge videos online this week, which are meant to raise money to fight amyotrophic lateral sclerosis (ALS), often called "Lou Gehrig's Disease." Hopefully, you've seen ours. We've watched a lot of these videos, but haven't seen one that makes an alt-fuel point quite like a new video from Toyota. Julie Hamp, the CCO of Toyota North America, lost a sister-in-law to ALS last year, so for her the cause is personal. Instead of just dumping icy-cold water on her head, Hamp uses water from the FCV fuel cell vehicle parked next to her. Because, of course, a hydrogen fuel cell car emits nothing but water vapor. Toyota didn't run a lot of hydrogen through the car to collect water, it just got enough to top off the ice bucket. Using the water emissions from a hydrogen vehicle in a creative way is not a new trick. Two years ago, the California Fuel Cell Partnership made the point that you can drink the emissions (just like Mercedes-Benz did earlier this year), but admitted that "fuel cells produce about the same amount of water as gasoline vehicle – about 1/3 cup for a full day of driving." Still, for a good cause, we'll accept the mix of tap water and "emissions." Check out the video below, if you haven't had enough already. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.