2006 Toyota 4runner Sr5 Sport Utility 4-door 4.0l on 2040-cars

Auto blog

How many Toyotas are potentially affected by seat fabric problem?

When we reported yesterday on Toyota's stop-sale order of certain 2013 and 2014 models due to an issue with the fabrics on models with heated seats not conforming to flammability regulations, one of our many questions was how many vehicles were affected? More importantly, how many of those cars have already found homes?
Kelley Blue Book has the troubling statistics. Every 2013 and 2014 Avalon features heated seats. 6.2-percent of 2013 and 4.5-percent of 2014 Camry sedans, meanwhile, were sold with heated seats. That doesn't seem as bad as 100-percent of the larger Avalon, until you consider the Camry's huge volume - the 5.6-percent average still accounts for a lot of cars. Sienna minivans are heavily affected as well, with a total of 37-percent of 2013s and 46-percent of 2014s fitted with butt warmers. The stop-sale only affects 7-percent of 2014 Corolla models, but like the Camry, that number is rather misleading due to the sheer volume of cars Toyota moves. You can see the entire breakdown of percentages by clicking on the inset image.
According to Karl Brauer, a senior analyst for KBB, this problem comes at the worst possible time. "Given that much of the US is currently in the grips of a record cold snap, there's sure to be high demand for models with seat heaters," Brauer notes. The stop-sale order is a good first step, but it doesn't do anything to inform consumers who currently own the affected models and may, in these frosty temperatures, want to use their seat heaters. "Should owners of those vehicles stop using the seat heaters?" Brauer asked.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

This classic Firebird restomod swallowed a Prius

It takes an unusual eye to look at a 1967 Pontiac Firebird and see the Toyota Prius hidden inside. But that's just the kind of eye that a creative mechanic known online as "Bill the Engineer" has. Bill is updating his old Firebird into a true classic for the 21st century and has documenting the changes over at Priuschat and EcoModder. The TL,DR version of the story: he's replacing the worn-out powertrain with the gas-electric hybrid one from a Prius V, because it turns out the two vehicles have almost exactly the same wheelbase. Bill, who's from Columbus, Ohio and doesn't want his full name used, said in his posts on the conversion project that he's made many memories with this vehicle since buying it back in 1979. Since then, a few moves, a few decades, and some time in storage meant that the car would no longer function as he wanted it to. As he wrote, "when it comes to mice in the vehicles IT IS WAR." His solution is to make new memories and making a greener vehicle, and so we wanted to ask him how things have been going. Bill's been traveling a bit recently, but told AutoblogGreen that he's now figuring out the next steps for this amazing and complicated project. "I always plan things out before I do them," he said. That's the only way something like this can work. ABG: I think we have to start with what gave you the inspiration for this project. Was it simply that you had the two cars and wanted to see them merged into one cool mashup, or was it something else? "One day my wife wondered out loud if the car could be converted into a hybrid... The rest is history." Bill: I have been the owner of my 1967 Firebird convertible since 1979 when I bought it for $750.00. I drove it for years and made many memories. Afterward it was in storage for many years during which time mice at their way into the car and trashed the interior and wiring. I started working on a conventional restoration but always ran into major problems with hidden corrosion, electrical issues and an engine on its last legs. The car was never going to be as nice as I wanted going the conventional route. One day my wife wondered out loud if the car could be converted into a hybrid like our two daily driver Prii. That got me thinking about how it could be done. The rest is history... ABG: It looks like you started in late 2014. Have things gone well since then, or has it been one hassle after another? What has been the biggest setback, and what were the biggest victories?