Suv 3.0l Awd 3rd Row Leather Power Seats Navigation Dual Climate Heated Seats on 2040-cars

Auto blog

Automakers drop support for Trump effort against California emissions

WASHINGTON — Toyota, Fiat Chrysler (now known as Stellantis following its merger with Peugeot) and other major automakers said on Tuesday they were joining General Motors in abandoning support for former President Donald Trump's effort to bar California from setting its own zero emission vehicle rules. The automakers, which also included Hyundai, Kia, Mitsubishi, Mazda and Subaru, said in a joint statement they were withdrawing from an ongoing legal challenge to California's emission-setting powers, "in a gesture of good faith and to find a constructive path forward" with President Joe Biden. The automakers, along with the National Automobile Dealers Association, said they were aligned "with the Biden administrationÂ’s goals to achieve year-over-year improvements in fuel economy standards." Nissan in December withdrew from the challenge after GM's decision in November shocked the industry and won praise from Biden. On Monday, the Justice Department asked the U.S. Appeals Court for the District of Columbia to put the California emissions litigation on hold to "ensure due respect for the prerogative of the executive branch to reconsider the policy decisions of a prior administration." Biden has directed agencies to quickly reconsider TrumpÂ’s 2019 decision to revoke CaliforniaÂ’s authority to set its own auto tailpipe emissions standards and require rising numbers of zero-emission vehicles, as well as Trump's national fuel economy rollback. Asked to respond to the automakers' action, White House climate adviser Gina McCarthy said in a statement that "after four years of putting us in reverse, it is time to restart and build a sustainable future, grow domestic manufacturing, and deliver clean cars for America." California Governor Gavin Newsom praised the automakers on Twitter for "dropping your climate-denying, air-polluting, Trump-era lawsuit against CA" and urged them to join the voluntary framework. TALKS WITH BIDEN Separately, an industry trade group on Tuesday proposed to start talks with Biden on revised fuel economy standards that would be higher than Trump-era standards but lower than ones set during the prior Democratic administration. The Trump administration in March finalized a rollback of U.S. Corporate Average Fuel Economy standards to require 1.5% annual increases in efficiency through 2026, well below the 5% yearly boosts under the Obama administration rules it discarded.

2020 Subaru Outback Suspension Deep Dive | More than meets the eye

The 2020 Subaru Outback is a completely redesigned car. It has a lot to offer in terms of new convenience features, and the driving experience is much improved. A good deal of that comes from chassis improvements, and indeed a lot of work went into making the body shell and suspension subframes more rigid so the suspension attachment points could be more robust and stable. Don’t let all of that rigidity talk make you think the ride itself is stiff. It isnÂ’t. Any suspension tuning engineer will tell you that a stable platform is necessary even if a smooth ride is the goal. Rigid attachment points make it easier to control ride motions and road imperfections within those components designed for that very job – the springs, dampers and suspension bushings. So letÂ’s take a look at what Subaru has done under the new Outback. What weÂ’re about to see doesnÂ’t just apply to the Outback wagon, but to the closely-related and also-redesigned 2020 Legacy sedan as well.   ItÂ’s no surprise that a vehicle like the Subaru Outback uses strut front suspension, but from here, a couple of details do look curious.   Like any strut suspension, the steering axis (yellow line) is defined by the pivot bushing at the top of the strut and the center of the lower ball joint. The entire affair will pivot about this line when the wheels are turned. The lower control arm (red) of the newly redesigned 2020 Outback is now a lightweight aluminum piece instead of the steel hunk that was used last year. As before, thereÂ’s a “direct-acting” stabilizer bar link (green) that attaches to the strut housing, an arrangement that maximizes the efficiency of the stabilizer bar because the motion ratio is 1-to-1 motion with respect to wheel movement. As for the stabilizer bar itself, itÂ’s now hollow to save a bit of weight.   This spacer (yellow) raises the body relative to the suspension. The Outback has one, but the lower-riding Legacy sedan does not. The spacer pushes the arm down (or the body up - take your pick), so that means the OutbackÂ’s reinforcing bracket (green) will also differ from that of the Legacy. While weÂ’re here, look at the round rubber bushing just below the spacer. That void space and square nub you see pointing directly at you will make sense in a short while.   Subaru couldnÂ’t simply put a spacer on the OutbackÂ’s rear lower control arm pivot and call it good. They had to do something of similar magnitude at the front.

Subaru says Japan car output halted due to defective part

TOKYO — Subaru Corp said its sole car factory in Japan accounting for roughly 60 percent of global production had halted output a week ago after it discovered a defect in a component procured from a supplier. The Asahi newspaper first reported the suspension at the Gunma plant on Wednesday, saying the defect was found in the power steering component. A spokesman for Subaru says the problem affecting Crosstreks and Foresters was discovered early. None of the affected vehicles had reached consumers, and won't until they've been repaired. Perhaps 10,000 cars, maybe fewer, were intended for the U.S. market. Subaru, which exports the majority of its domestically made cars, could not say when production would resume. Production at Subaru's plant in Indiana was unaffected.Related Video: Plants/Manufacturing Subaru