2002 Subaru Impreza Wrx Sedan 4-door 2.0l Fixer Upper Doesn't Pass Nysi on 2040-cars

Auto blog

Subaru recalling 660k vehicles in some states for possible brake line corrosion

Subaru is recalling 660,238 vehicles located in 20 US states that use salt on their roads. It's possible that salty water could splash onto the rear brake lines, and it could eventually cause corrosion and potentially perforation, leading to a fluid leak.
The recall covers the 2005-2009 Outback and Legacy, 2008-2011 Impreza, 2008-2014 WRX and STI and 2009-2013 Forester. However, only vehicles currently or formerly registered in the following snowy US states or districts are covered: Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. The company previously recalled the 2005-2009 Legacy and Outback to repair this problem, and now it's added the additional models, plus any of the original cars it missed the first time.
According to the defect notice from the National Highway Traffic Safety Administration, Subaru found a total of 24 cases of corrosion in US leading up to the recall. There was a single case of actual brake line perforation, but it happened in Switzerland, according to the document. The company believes that it would take seven or more seasons of winter driving on salty roads before any corroding would begin.

Subaru, like Nissan, admits improper checks on Japan cars, expects recalls

TOKYO — Subaru on Friday said it had failed to follow proper inspection procedures for vehicles for the domestic market, an issue likely to result in a product recall and adding to a list of compliance problems at Japanese companies. The automaker said for more than 30 years, final inspections of new vehicles at its main Gunma complex north of Tokyo were sometimes conducted by inspectors who were not listed as certified technicians, violating transport ministry requirements. The automaker said it was therefore considering recalling about 255,000 vehicles including its Legacy, Forester and Impreza models produced at the complex and sold at home, at a cost of around 5 billion yen ($43.86 million). Chief Executive Officer Yasuyuki Yoshinaga at a news conference said inspectors in training for certification to sign off final checks had been approving the checks under the names of their trainers, a process the automaker followed for over 30 years without realizing it did not meet ministry requirements. "The final inspection process is very important and we acknowledge that we did not meet requirements," Yoshinaga said. "It's always been my goal to make this company good. This issue shows that we're not there yet." Subaru said it would report details of an internal investigation to the ministry on Monday, and that it needed to better communicate requirements to workers. "It's always been my goal to make this company good. This issue shows that we're not there yet." The revelation followed a similar oversight at Nissan, while Kobe Steel has been grappling with a data fabrication scandal, tarnishing Japan's reputation for quality control. Yoshinaga said the issue was discovered during an internal inspection ordered by the ministry after Nissan late last month revealed similar violations on inspections governing vehicles sold in Japan at its domestic factories. The ministry requires certified technicians to sign off on paperwork for final inspections for vehicles produced in Japan for the domestic market. The extra step does not affect product quality and is not needed for vehicles exported overseas. Toyota, Honda and other Japanese automakers on Friday said they have reported to the ministry that they found no issues with their respective inspections. Subaru shares closed down 2.6 percent on Friday after falling more than 3 percent following media reports of the improper inspections. The broader market rose 1.2 percent.

New Subaru concept crossover EV shown in walkaround video

Subaru held a technology briefing this week in Tokyo where it announced ambitious sustainability goals, but nearly lost amid the discussion of converting its fleet over to electricity was the unveiling of what appears to be an early concept version of a forthcoming battery-electric crossover. Thanks to the Japanese YouTube account LoveCars!TV!, we get a walkaround look. It appears to be Subaru’s version of the crossover EV it is jointly developing with Toyota, to be built atop a flexible platform that can accommodate multiple production vehicles from both brands. What weÂ’re shown is an athletic-looking crossover with its wheels pushed to the corners that borrows design elements, for better or for worse, from Cadillac, the Pontiac Aztek and the Tesla Cybertruck. Up front, the crossover borrows and exaggerates CadillacÂ’s signature squared-off corners and deep fog-light scoops that also reminds us of InfinitiÂ’s Q Inspiration concept from the 2018 Detroit auto show. It opts for narrow LED headlamps, and it notably omits any aesthetic concession to even a faux grille, save for a hexagonal shape outlined by the panel seams. Coupled with the black cladding on the lower bumper, the crossover's face has a certain Batman-logo shape to it. Moving around to the side, we see heavy black cladding — it doesn't appear to be standard plastic, since it reflects light — around the wheel wells, lending them a semi-octagonal shape that evokes the strongest comparison to the polarizing Cybertruck. Coupled with some interesting side creases, the cladding also gives the appearance that the wheel wells bulge out, and that the doors pinch inward, more than they probably do in reality. There are also no door handles or brakes, the side mirrors are rearview cameras and the windows are blacked out, so thereÂ’s nothing to divine about the interior and how far along that is in conceptualization. In back is where things get especially weird and Aztek-like, with a blunt and upright rectangular body panel making up the tailgate underneath a generously long, sloping rear window. ItÂ’s beveled at the top to tuck underneath the rear LED light bar, which stretches the length of the glass, and curved on each end to integrate with the sides. The LED treatment also dives down 90 degrees from the horizontal rear bar and then makes another sharp 90-degree jag to bracket the rear panel in hard-angled brake lights.