Mega Cab 4x4 Diesel New 6.7l 350 Hp Horsepower 4 Doors 4-wheel Abs Brakes on 2040-cars

Auto blog

NHTSA closes investigation on 4.7M FCA power modules, no recall

FCA US hasn't had the best time with recalls as of late. Not only did the company recently agree to greater safety oversight and paid $105 million to the government, that came just days after hacking fears prompted a 1.4-million model recall campaign. However, a recent decision to close an investigation by the National Highway Traffic Safety Administration means that the automaker doesn't have to worry about another major recall possibly affecting 4.7 million vehicles, according to the agency's report (as a PDF). Last September, the Center for Auto Safety petitioned NHTSA to investigate an alleged problem with the totally integrated power module (TIPM) on these FCA US models. The group claimed that a fault with the component could cause a variety of maladies, including stalls, not starting, catching fire, unintended acceleration, and airbag non-deployment. At the time, it also submitted 70 cases where this had reportedly happened. According to NHTSA, "no valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration, or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components." The agency did find signs of an issue with the fuel pump relay in some Jeep Grand Cherokees and Dodge Durangos, but FCA US issued recalls for the problem in September 2014 and February 2015. Without anything else to go on, the Feds don't think it's worth investigating this topic any more.

Three Ram recalls affect more than a million pickups

Millions of Ram pickups across many of its model lines in the US are in need of recall repairs due to three campaigns by the truck maker. The largest of this trio covers 1.06 million examples in the US of the 2012-2014 Ram 1500, 2500, 3500, and chassis cab versions of the 3500, 4500, and 5500 because of potential inadvertent driver-side airbag deployment. In addition to those affected here, there are 235,925 in Canada, 26,543 in Mexico, and 23,635 elsewhere. There are also two related injures from this problem, but no reports of accidents, according to the company. While the recall was mysteriously ignored in the media at the time, the National Highway Traffic Safety Administration announced details of this campaign in late July. The next largest among the three covers 188,000 examples of the 2014 and 2015 Ram 1500 Quad Cab in the US because their side-curtain airbags don't fully overlap the C-pillars when deployed, which is in violation of federal rules. Conceivably, rear passengers not wearing their seatbelt could be more likely to be ejected in a crash. Ram's repair for the issue is still being developed, according to the National Highway Traffic Safety Administration, but the company advises all occupants to be buckled in. The final campaign affects 156,498 the company's heavy-duty trucks in the US, including the 2013 Ram 3500 and 2014 Ram 2500, 3500, and 3500 Chassis Cab. In addition, there are 20,603 in Canada and 3,241 elsewhere. Of the 13,236 in Mexico, a few units of the 2014 Ram 1500 exclusive to that market are also covered. The company found that the welds for some steering parts might have "insufficient fusion." If the part breaks, then vehicles are still controllable but with diminished response. There are no reported injuries but one minor accident. The fix involves installing a reinforcement bracket. Related Video: Statement: Steering-wheel Wiring Harness September 10, 2015 , Auburn Hills, Mich. - FCA US LLC is conducting a voluntary safety recall to inspect and service, as required, wiring harnesses in an estimated 1.06 million U.S.-market trucks. Investigation by FCA US discovered certain trucks may have steering-wheel wiring harnesses that wear because of contact with a spring. Such wear may cause a short-circuit that may lead to inadvertent driver-side air-bag deployment. The Company is aware of two related injuries, but no accidents.

Stellantis aims to eliminate separate inverter, charger to improve EV efficiency

Stellantis has announced that, in collaboration with French battery company Saft and French National Center for Scientific Research, has made significant progress in eliminating two major components of an electric vehicle powertrain: the on-board charger and the power inverter for the motor. The company claims that doing this will allow for better space use in vehicles, as well as improvements in efficiency, cost and reliability of components. As a quick primer, also explained in the below video, the on-board charger and power inverter are sort of translators to get the right current to different parts of the electric powertrain. The on-board charger takes AC power from the grid and converts it to DC to charge the batteries. Then when power goes from the batteries to the electric motor, the power inverter converts that DC power back to AC. These components aren't exactly small. Frequently you'll find them packaged somewhere under the hood. What Stellantis and its cohorts have developed, and have been using on a test vehicle since last summer, are small power inverter boards that can be mounted very closely to the battery packs. They can handle both conversion needs, for charging and discharging, instead of needing two separate devices. The most obvious perk to this is that you can do away with those traditional components and free up more space, either for making smaller vehicles without losing interior volume, or adding space to a vehicle that wouldn't have had it otherwise. There's the additional benefit of reduced weight, something that EVs struggle with. Stellantis also claims improvements in efficiency, reliability, and cost, however, it didn't go into detail as to how this setup would do that exactly. We'll try to get in touch with representatives from Stellantis in order to get more information. We're still a ways out from seeing this technology in production Stellantis vehicles. The company said it aims to apply it to vehicles by the end of the decade. Saft is also looking at using it on stationary battery systems as well. So maybe we'll see it on a 2029 Ram 1500 REV, but for now, we'll be living with traditional chargers and inverters. Related Video: Green Alfa Romeo Chrysler Dodge Fiat RAM Technology Electric