2013 Ram 3500 Laramie Crew Cab Diesel 4x4 At Douglasdodge.com on 2040-cars

Auto blog

Three Ram recalls affect more than a million pickups

Millions of Ram pickups across many of its model lines in the US are in need of recall repairs due to three campaigns by the truck maker. The largest of this trio covers 1.06 million examples in the US of the 2012-2014 Ram 1500, 2500, 3500, and chassis cab versions of the 3500, 4500, and 5500 because of potential inadvertent driver-side airbag deployment. In addition to those affected here, there are 235,925 in Canada, 26,543 in Mexico, and 23,635 elsewhere. There are also two related injures from this problem, but no reports of accidents, according to the company. While the recall was mysteriously ignored in the media at the time, the National Highway Traffic Safety Administration announced details of this campaign in late July. The next largest among the three covers 188,000 examples of the 2014 and 2015 Ram 1500 Quad Cab in the US because their side-curtain airbags don't fully overlap the C-pillars when deployed, which is in violation of federal rules. Conceivably, rear passengers not wearing their seatbelt could be more likely to be ejected in a crash. Ram's repair for the issue is still being developed, according to the National Highway Traffic Safety Administration, but the company advises all occupants to be buckled in. The final campaign affects 156,498 the company's heavy-duty trucks in the US, including the 2013 Ram 3500 and 2014 Ram 2500, 3500, and 3500 Chassis Cab. In addition, there are 20,603 in Canada and 3,241 elsewhere. Of the 13,236 in Mexico, a few units of the 2014 Ram 1500 exclusive to that market are also covered. The company found that the welds for some steering parts might have "insufficient fusion." If the part breaks, then vehicles are still controllable but with diminished response. There are no reported injuries but one minor accident. The fix involves installing a reinforcement bracket. Related Video: Statement: Steering-wheel Wiring Harness September 10, 2015 , Auburn Hills, Mich. - FCA US LLC is conducting a voluntary safety recall to inspect and service, as required, wiring harnesses in an estimated 1.06 million U.S.-market trucks. Investigation by FCA US discovered certain trucks may have steering-wheel wiring harnesses that wear because of contact with a spring. Such wear may cause a short-circuit that may lead to inadvertent driver-side air-bag deployment. The Company is aware of two related injuries, but no accidents.

Analysts wary over FCA lawsuit but say emissions not as bad as VW

MILAN - Any potential fines Fiat Chrysler (FCA) may need to pay to settle a US civil lawsuit over diesel emissions will unlikely top $1 billion, analysts said, adding the case appeared less serious than at larger rival Volkswagen. The US government filed a civil lawsuit on Tuesday accusing FCA of illegally using software to bypass emission controls in 104,000 vehicles sold since 2014, which it said led to higher than allowable levels of nitrogen oxide (NOx) that are blamed for respiratory illnesses. FCA's shares dropped 16 percent in January when the U.S. Environmental Protection Agency (EPA) first raised the accusations, adding the carmaker could face a maximum fine of about $4.6 billion. The stock has been under pressure since. Volkswagen agreed to spend up to $25 billion in the United States to address claims from owners, environmental regulators, U.S. states and dealers. FCA, which sits on net debt of 5.1 billion euros ($5.70 billion), lacks VW's cash pile but analysts said its case looked much less severe. While VW admitted to intentionally cheating, Fiat Chrysler denies any wrongdoing. Authorities will have to prove that FCA's software constitutes a so-called "defeat device" and that it was fitted in the vehicles purposefully to bypass emission controls. Even if found guilty, the number of FCA vehicles targeted by the lawsuit is less than a fifth of those in the VW case. Applying calculations used in the German settlement, analysts estimate potential civil and criminal charges for Fiat Chrysler of around $800 million at most. Barclays has already cut its target price on the stock to take such a figure into account. Analysts also noted that FCA's vehicles are equipped with selective catalytic reduction (SCR) systems for cutting NOx emissions, so it is likely that any problem could be fixed through a software update. "Should this be the case, we estimate a total cost per vehicle of not more than around $100, i.e. around $10 million in aggregate," Evercore ISI analyst George Galliers said in a note. The estimates exclude any additional investments FCA may be asked to make in zero emissions vehicles infrastructure and awareness as was the case with VW. FCA said last week it would update the software in the vehicles in question, hoping it would alleviate the regulators' concern, but analysts said it may have been too little too late. The carmaker is also facing accusations over its diesel emissions in Europe.

Ram wants its midsize truck situation 'fixed soon'

The rumors of a midsize Ram pickup are like a metronome — sometimes in motion, sometimes dead. This week the rumor is alive, so reports Automotive News. Fiat Chrysler CEO Mike Manley admitted during an earnings call that the lack of a mid-sizer is "a clear hole in our portfolio," and that the Ram product development team is "focused on it." Puzzling that out means finding "a cost-effective platform in a region where we can build it with low cost and it still being applicable in the market." But he wants a solution found soon. During the product roadmap presentation FCA made in June last year, late CEO Sergio Marchionne said the middling pickup would be built in Mexico. That tidbit came after years of Marchionne saying the brand would get in the segment, only to have the idea shot down by Ram bosses. At the 2012 Detroit Auto Show, a year after the midsize Dodge Dakota went off the market, Marchionne said the brand would reinstate a new-generation Dakota, with a better-than-50% chance it would be unibody. In 2013, then-Ram president Reid Bigland said the chances were tiny because the numbers didn't add up. The two men got on the same page, in favor of, in 2014. In March 2016, Marchionne said, "I like that space a lot," and "It's a good space to be in." Exactly one month later, then-Ram CEO Bog Hegbloom said the idea was dead because he couldn't make a business case for it. Come early 2018, even Marchionne had joined the naysayers. He told Automobile, "We did not think it was necessary to re-enter that market after our last experience." The snag was, and remains, that a smaller truck has "a cost structure very similar to our Ram 1500. We have not found an economic way to get this done." Four months later, there's a midsize pickup on the product roadmap. Then, at this year's New York Auto Show, Ram Trucks boss Jim Morrison told us Ram had no plans yet for a smaller pickup, although the division continues to look at its options. Last September an Automotive News report forecast the truck to be built in Toledo alongside the Jeep Wrangler and Gladiator pickup. When Car and Driver asked for clarification about Toledo or Mexico, FCA pointed to Marchionne's comments referring to Mexico. It appears that's the angle Manley and his team are still trying to make work. The Saltillo, Mexico, assembly plant now builds Ram's heavy-duty trucks, but observers expect HD production to move to the U.S. to make room for the smaller pickup.