2014 Ram 2500 Tradesman on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

FCA and Cummins named in diesel emissions class-action lawsuit

Chrysler is now the first United States-based carmaker to be sued for allegedly skewing emissions results. In a move that sounds eerily similar to the troubles of European manufacturers, Chrysler is claimed to have hid diesel engine characteristics causing emissions as much as 14 times higher than permitted by regulations. According to Bloomberg, the lawsuit alleges that Chrysler, together with its diesel engine partner Cummins, has concealed the nitrogen oxide output of certain Ram vehicles produced between 2007 and 2012. The NOx pollutants were meant to be broken down in a process called regeneration in the truck's NAC system, or NOx Absorption Catalyst, which predated the 2013-introduced SCR, or Selective Catalytic Reduction system. By design, the NAC captures and stores NOx emissions, converting them to nitrogen and oxygen through a catalytic process. The lawsuit claims the Cummins engine's system has a limited capacity to store the emissions, and as a result the pollutants escape, increasing emissions, worsening fuel consumption and wearing down the catalytic converter. The later, cleaner SCR system uses a urea-water injection, and it gradually replaced the NAC on Cummins 6.7-liter engines, as it was first implemented in 2011 and made standard in 2013. As Bloomberg notes, the model years of Ram trucks involved in the lawsuit predate the earliest Volkswagen "Dieselgate" models by two years. The lawsuit, filed on behalf of 500,000 truck owners, accuses Chrysler and Cummins of fraud, false advertising and racketeering. As an underlying motive, the filing mentions a 2001 change in EPA emissions standards. Announced to become effective in 2010, the EPA requirements drove Chrysler and Cummins to try and reach those already by 2007. However, the NAC system is said to have fallen short of these goals, and the filing claims that Chrysler and Cummins chose to "rig" the engines instead. The affected vehicles predate the 2014 merger of Chrysler and Fiat. FCA US has released a statement regarding the lawsuit, saying it will contest the lawsuit "vigorously". News Source: BloombergImage Credit: Getty Editorial Government/Legal Green Chrysler Dodge RAM Emissions Diesel Vehicles FCA cummins diesel

Chrysler recalling 278,222 trucks and SUVs over bad rear axles

Chrysler has issued a recall of 278,222 light trucks and sport utility vehicles here in the United States. The reason: bad rear axles. Specifically, according to the National Highway Traffic Safety Administration, the rear axle pinion nut may lack a necessary adhesive patch, which could cause the nut to loosen. If this happens, the axle can lock up, which could cause all sorts of havoc on the road.
This is an expansion of the rear axle recall announced in October of last year, where 44,300 Ram 1500 and Dodge Dakota models were being called in. At that time, 12 accidents had been reported due to the faulty axle pinion nut.
Affected vehicles include Ram 1500 trucks from the 2009 to 2012 model years, Dodge Dakota models from the 2009 to 2011 model years, and both the Chrysler Aspen and Dodge Durango SUV twins, both from the 2009 model year only.