2013 St Quad 2wd 20s Aluminum V8 Hemi Lifetime Powertrain Warranty on 2040-cars

Auto blog

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

Inline-6 Hemi replacement on the cusp of production from Stellantis

It appears that Stellantis is ready to put its long-rumored inline-six into production at its Saltillo, Mexico plant, possibly marking the beginning of the end of Chrysler's long-running 5.7L Hemi V8. But so far, the automaker's American brands have remained mum on where exactly the new turbocharged "Tornado" I6 may land. Stellantis powertrain blog Stellpower (by way of Muscle Cars & Trucks) spotted an entry for a new "GME T6" inline-six engine on the Saltillo facility's web site, suggesting that it was either in production or close to it. That entry has since been removed, but the mystery remains.  We've been hearing tidbits here and there about this new inline engine for years, but this is the first time we've seen anything suggesting its arrival is imminent. Usually, such a significant powertrain update would coincide with the launch of a new product to showcase it. So far, Stellantis has remained mum, even overseas, about where this engine is destined to reside. 2022 model year vehicles are likely off the table entirely.  But while it's common for new engines to debut with new cars and trucks, it's not a universal truth. Ford's Coyote V8 missed the corresponding Mustang refresh by a year, for example, orphaning the 2010 model and its much-needed styling updates with the old 4.6L V8 (and the 3.8L V6, for that matter; the 3.7L Duratec was also late to that party). Even sticking just to Stellantis, the JL Wrangler's powertrains have been a work in progress since it arrived back in 2018. The standard V6 and 2.0-liter turbo-4 debuted at launch; the EcoDiesel, 392 and 4xe all came later.  And 4xe may be the model by which to measure our expectations. Its introduction didn't come completely out of nowhere, but it was rather sudden for what turned out to be such a solid offering. That bodes well for the company's existing Hemi-powered trucks and SUVs. The Ram 1500, Jeep Grand Cherokee and Wagoneer are all strong candidates to receive the new Hemi replacement, as all would greatly benefit from even small improvements in fuel economy. If there's to be a future for the Dodge Charger and Challenger and Chrysler 300, they'd benefit too. And how about a Gladiator with the wick turned up, positioned as its equivalent to the Wrangler 392. Turn that Tornado into a Dust Devil. Don't worry; we've got plenty more where that came from.  Related Video This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Prosecutors indict three FCA employees in alleged emissions-cheating case

Federal prosecutors indicted three Fiat Chrysler Automobiles (FCA, now Stellantis) employees as part of an investigation into alleged emissions cheating. Charges unsealed on April 20, 2021, accuse the defendants of helping rig the emissions control system fitted to the 3.0-liter turbodiesel V6 used in some models during the 2010s. Prosecutors claim Emanuele Palma, Sergio Pasini, and Gianluca Sabbioni played a determining role in developing a defeat device that allowed the V6 to obtain certification from the Environmental Protection Agency (EPA) while polluting too much in normal driving conditions. Jeep and Ram began making the engine available in the Grand Cherokee and the 1500, respectively, in 2014, but the charges state plans to game the EPA started in 2011. Palma, Pasini, and Sabbioni knowingly mislead federal regulators, the charges claim; they called it "cycle beating," according to The Detroit News. While the three men were part of FCA's research and development department, they started the project while working for an Italian supplier named VM Motori, which FCA purchased in 2013. Pasini and Sabbioni are each charged with one count of conspiracy to defraud the United States and to violate the Clean Air Act, one count of conspiracy to commit wire fraud, and six counts of violating the Clean Air Act. They could spend several years behind bars if they're found guilty. Both are currently in their home country of Italy. Palma's legal troubles are more serious. He was charged with several counts in September 2019, though four wire fraud charges were dropped in November 2020. He lives in Bloomfield Hills, a city located on the far outskirts of Detroit. Prosecutors claim motorists spent over $4 billion on over 100,000 trucks and SUVs fitted with the non-compliant engine between January 2013 and September 2017. FCA has already agreed to pay $800 million to resolve civil claims from the Justice Department, state officials and customers, though it significantly has not admitted guilt. It stressed that "it did not engage in any deliberate scheme to install defeat devices to cheat emissions tests."