2012(12) Ram 1500 Slt Quad Cab 4x4 V8 6'4 Box Warranty Only 18k Black 1 Owner on 2040-cars

Auto blog

All hail the Hellephant, Mopar's 1,000-horsepower crate engine

It's shocking to say this, but the all-powerful Dodge Demon looks weak now that Mopar has unleashed the Hellephant. This crate motor makes 1,000 horsepower and 950 pound-feet of torque, and its name is a combination of the nickname for the old 426-cubic-inch Hemi V8 and, obviously, the Hellcat. This monster is a 426-cubic-inch version of the current third-generation Hemi V8 topped by a supercharger similar to what the Hellcat line packs. Everything is cranked up to — or perhaps, past — 11. The engine block is made of aluminum and weighs 100 pounds less than the equivalent iron block. All of the internals are forged. The stroke and bore have been increased. The supercharger produces 15 pounds of boost and displaces 3 liters; more than the 2.7-liter blower on the Demon and the 2.4-liter blower on the Hellcat. And as big and powerful as it is, it will still rev to 7,000 rpm. It's a thoroughly monstrous motor, but shockingly, it won't be that difficult to live with. For one thing, Mopar will offer a complete kit to get the engine up and running, including an engine computer, wiring harness and drive-by-wire throttle. It also runs on 93-octane pump gas. That's especially amazing considering the Demon engine "only" makes 840 horsepower, and that's on race gas with 100+ octane fuel. It also has us wondering what the Hellephant could make on racing fuel. The Mopar folks did say that there's room to add more power. Pricing wasn't announced for the Hellephant engine. The Hellcat crate engine retails at $19,350 directly from Mopar, so it's safe to assume that the Hellephant will go for more. The installation kit with the computer and harness will be an extra charge of likely over $2,000, based on the Hellcat kit. The engine and the kit will be available in the first quarter of 2019. Related Video: Featured Gallery Hellephant Crate Engine SEMA Show Chrysler Dodge Jeep RAM Performance dodge demon hellephant

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

Chrysler thinking of taking on Ford SVT Raptor?

An argument could be made that Chrysler already offers a competitor to the much-loved Ford Raptor in the form of the Ram Runner pickup. The difference, though, is that Ford builds the Raptor right on the production line, whereas Ram requires the buyer to have modifications made at one of its dealerships after the initial purchase is made.
That distinction may soon be a thing of the past, according to a report from Wards Auto. "If we could see that the volume was significant enough that it makes sense to do it, we'll do it," says Pat Dougherty, vice president of Mopar parts, sales and field operations. "But if we don't, then we'll continue to do it the way we do it."
Additionally, Chrysler would reportedly like to put more emphasis on the fuel efficiency of its off-road-ready lineup, which is spearheaded by the Jeep Wrangler. Says Dougherty, "For a lot of the people who go off-roading (but) actually drive their vehicle as a daily driver, they want to make sure they're getting fuel efficiency while they're driving to work."