2012 3500 Dually Quad Cab Diesel 4x4 6 Speed Manual Slt on 2040-cars

Auto blog

Chrysler's internal documents question Ram quality as workers protest

Chrysler is reportedly having a hard time ramping up production of its 2013 Ram 1500. According to The Detroit News, only 16 of the 58 trucks built at the Warren Truck Assembly Plant during the model's first hour passed final inspection. While quality eventually improved over the course of the day, just over half of the units built on Thursday were approved for shipment. Even with workers ordered to stay late to fix their mistakes, some 1,078 units remained outside the facility with defects. The problem, according to workers at the plant, is morale.
According to the report, Chrysler recently changed the shift schedule at the plant and workers are unhappy with the new situation. The new plan has workers split into three shifts, each covering four 10-hour days. With the shifts staggered, some workers now have to work nights and on Saturdays. Some employees are so upset that they've taken to protesting, though the move isn't sanctioned by the United Auto Workers.
Meanwhile, Chrysler admits there were internal issues with the launch, but that the company was able to contain them. A spokesperson has said "plant quality indicators are getting progressively better."

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.