Big Horn 4x4 Hemi Nerf Bars Mp3 Sirius Xm Navigation Uconnect Camera Alloy Rims on 2040-cars

Auto blog

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.

Chrysler called out over lackluster Ram Runner by racer who helped develop it

Fans of off-roading and desert blasting might recall that Chrysler offers an aftermarket conversion that can turn a Ram 1500 into a road-legal desert racer, called the Ram Runner. The kit, sold through Mopar, includes some significant suspension upgrades, body tweaks and a brawnier cat-back exhaust for the truck's 5.7-liter V8.
Considering all of this, comparisons with the almighty Ford F-150 SVT Raptor are common. Among the off-road community, that makes these two a sort of Chevrolet Camaro and Ford Mustang for people that prefer driving on dirt. In the Race-Dezert forum, the discussion as to which truck was better was proceeding as normal - Ram fans said their piece and Ford fans said theirs. Then, a man named Kent Kroeker offered up his two cents.
See, Kroeker is a Baja racer, and the man that helped develop the Ram Runner. Despite his association with the truck, though, he had some less than kind words for Chrysler and the Ram Runner.