2014 Ram 1500 Tradesman/express on 2040-cars

Auto blog

2021 Ram 1500 TRX Suspension Deep Dive | Underbelly of the beast

I think we can all agree that we have been waiting for a gonzo full-size truck like the 2021 Ram 1500 TRX for a long time. After all, it has been over a decade since the Ford F-150 Raptor came out, and it was such an immediate hit that I expected its direct competitors to respond much sooner than this. We all knew something was finally brewing in 2016, when the TRX concept was unveiled at the Texas State Fair. I was there, and was among the many who gave the assembled Ram higher-ups an enthusiastic thumbs-up. That’s what they were hoping to see before they greenlit the project. The pace of development being what it is, and with the redesigned, current-generation Ram 1500 a prerequisite that understandably had to come first, itÂ’s no surprise that weÂ’re only seeing it now as a 2021 model. You may be biting your tongue that I overlooked the Tundra TRD Pro or the Chevrolet Silverado Trail Boss, but neither of those comes close to following the formula established by the Raptor: big engine, a much wider stance than the base truck, greatly enhanced suspension travel, huge tires and swollen fenders to cover it all. Only the Raptor and the TRX fit that mold. For now.   Before I got started, I first pointed the TRX up my RTI ramp and measured its Flex Index score. Please excuse the shaded nose; the truck ran farther up than IÂ’d guessed and literally drove out of the picture. But something in my subconscious warned me to keep the garage door open, which was fortuitous because the nose of the Ram ended up inside. The TRX hiked its front wheel 29 and 7/8 inches off the ground before the left rear tire reached the point of lift-off, and that equates to a climb of 87.4 inches up the deck of my ramp. Divide that by the TRXÂ’s wheelbase of 145.1 inches, multiply by 1,000, and you arrive at a Flex Index score of 602 points. It could have been a few points higher, I think, if I could have straightened out the steering a bit better. But the high-grip cheese grater surface of my ramp was firmly dug in and having none of it. This is an extremely good score for a full-size crew cab pickup. LetÂ’s take a closer look at what made that possible.   The track width of the TRXÂ’s double wishbone front-suspension is a full 6 inches broader than a regular Ram 1500, and you are looking at the parts that are responsible. The lower wishbone (yellow arrow), the upper control arm (green) and the steering knuckle (red) conspire to add 3 inches per side to the TRXÂ’s stance.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Stellantis and Foxconn's new joint venture will focus on connectivity

MILAN — Carmaker Stellantis and TaiwanÂ’s Foxconn announced plans to develop a jointly operated automotive supplier focusing on technology to make vehicles more connected, including artificial intelligence-based applications and 5G communications. Stellantis CEO Carlos Tavares said the services that will be developed through the tie-up “will mark the next great evolution of our industry,” alongside fully electrified and hybrid powertrains. The deal brings together Stellantis, the worldÂ’s 4th-largest automaker formed this year by the merger of Fiat Chrysler Automobiles and PSA Peugeot, and Foxconn, a major supplier of iPhones. The companies said the venture would focus on such services as infotainment, the integration of telecommunications and computer systems, artificial intelligence-based applications, 5G communications, e-commerce channels and smart cockpit integration. The companies announced a non-binding memorandum of understanding to form a 50-50 joint venture called Mobile Drive, which will be based in the Netherlands and function as an automotive supplier also to other carmakers. The new venture will combine advanced consumer electronics, Human-Machine Interfaces (HMI) to create new services “that will exceed customer expectations,” the companies said in a release. “Customers today and, in the future, demand and expect ever-increasing software-driven and creative solutions to connect the drivers and passengers with the vehicle inside and out,Â’Â’ Foxconn Chairman Young Liu. Alfa Romeo Chrysler Dodge Ferrari Fiat Jeep RAM Citroen Opel Peugeot 5g Connectivity Stellantis Foxconn