2008 Mercury Grand Marquis Gs 4.6l V8 6pass Leather 24k Texas Direct Auto on 2040-cars

Auto blog

Ford recalls 300,000 Crown Vics over lighting module

The Basics: Ford is recalling 312,814 units of the Crown Victoria and Mercury Grand Marquis sedans from the 2003-2005 model years. They were built at the St. Thomas Assembly Plant between Oct. 3, 2001, and Aug. 2, 2005. Ford says 296,004 of those units are located in the United States, with another 14,714 in Canada and 2,096 in Mexico. The Problem: The solder joints on the lighting control module could crack, depriving the headlamps of the power they need to light the way ahead. That could increase the risk of a crash, particularly at night and in other low-visibility situations. Injuries/Deaths: Ford reports that it is aware of 11 accidents that resulted from the problem, leading to one injury described as "minor." The Fix: The manufacturer is instructing dealers to replace the entire lighting control module. If You Own One: Make sure your headlights are working before getting under way. If they're not, avoid driving under low-light conditions, including at night, in heavy precipitation, or in fog. Ford Issues Three Safety Recalls and One Safety Compliance Recall in North America DEARBORN, Mich., Dec. 22, 2015 – Ford Motor Company is issuing three safety recalls and one safety compliance recall in North America. Details are as follows: Ford Motor Company issues safety recall for certain 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles to replace lighting control module Ford Motor Company is issuing a safety recall for approximately 313,000 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles to replace a lighting control module. The solder joints on the module could crack and interrupt power to the headlamps – increasing the risk of crash at night. Ford is aware of 11 reports of accidents and one report of a minor injury related to this issue. Affected vehicles include certain 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles built at St. Thomas Assembly Plant, Oct. 3, 2001 through Aug. 2, 2005. There are a total of 312,814 vehicles that might be affected in North America, including 296,004 in the United States and federalized territories, 14,714 in Canada and 2,096 in Mexico. Dealers will replace the lighting control module at no cost to the customer. Ford issues safety recall for certain 2016 Ford F-650 and F-750 vehicles to replace rear air brake chamber Ford is issuing a safety recall for 177 2016 Ford F-650 and F-750 vehicles to replace the rear air brake chamber.

The 1965 Ford Mustang could have looked a lot different

The 1965 Ford Mustang is unquestionably an automotive design icon, and nearly every generation of Mustang has some connection to that original car. Because it's such a universally-known vehicle, we were amazed to see all the different designs that were being considered. Head of Ford's archives Ted Ryan recently shared photos of design proposals for the original Mustang on Twitter that he and Jamie Myler found, and we reached out to them to find out more. As Ryan initially noted, the photos were taken on August 19, 1962, and they are proposals for the Ford Mustang. Apparently Ford had committed to doing a Falcon-based youth-oriented car at this point, and it did have plans to launch the car in 1964 for the 1965 model year. But after having little success with early design proposals, the company asked all of its design studios — the Advanced Studio, Lincoln-Mercury Studio and Ford Studio — to submit proposals. With only about two years before the planned launch, Ford was understandably short on time, and it's believed that the studios only had a month to create and present these designs. Lincoln-Mercury design proposal View 8 Photos The majority of the designs, a total of five, came from the Advanced Studio, and part of this was because they already had a couple of concept designs in reserve it could present. Two other models representing three design possibilities came from Lincoln-Mercury, and just one model with two options came from Ford. The Advanced Studio proposals are shown in the gallery at the very top of this article, and the Lincoln-Mercury and Ford proposals are in the gallery directly above this paragraph. The Advanced Studio's most radical design is the one that was clearly related to the Mustang I concept that would be shown later that year with huge wraparound rear glass, turbine-inspired bumpers and enormous side scoops. The other proposals from the studio were more conservative, featuring simple lines, grilles reminiscent of the Falcon, and one even borrowing the jet-thruster-style taillights made famous on the Thunderbird. Lincoln-Mercury had some impressively bold designs, particularly its fastback that had buttresses to extend the shape all the way to the tail. This car had two different side trim possibilities. The other Lincoln-Mercury design was toned down a bit, but had two interesting possibilities for side detailing, as well as some crisp, low-profile tail fins.

Translogic drives wood-burning Mercury Beaver XR-7

You read the title right, we're talking about the Mercury Beaver XR-7. No, Mercury never officially built a car called the beaver. This is the brainchild of upstate New Yorker Chip Beam, who owns and operates Beaver Energy, LLC. It runs on gases created by wood pellets fermented in a 2,400-degree furnace and fed to a supercharged Ford 4.6-liter V8.
By all accounts, it gets down the road just fine, and has pretty close to full power. The best part is, you can grow the fuel yourself and avoid patronizing big oil, if that's your thing. The only drawback that we can see to the Mercury Beaver XR-7 is the PVC pipe jungle occupying the space that would be the trunk under normal circumstances.
Still, if you're willing to smell like a mountain man and look like a bad Back to the Future knockoff, this ride is right up your alley. Click past the jump to see Translogic's take on this modified Merc.