1970 Mercury Cougar - Runs Strong - Drive While You Restore! on 2040-cars

Auto blog

This Mercury Cougar Eliminator is a lovely '69 survivor

If you have an overachieving brother/sister/cousin/friend (or whoever), you might know this feeling well; it can be tough to live up to those standards. In many ways, that notion can also describe the Mercury Cougar and its pioneering Ford Mustang sibling. Quite the act to follow, no? Happily though, the Cougar proved to be different enough from its Mustang relative to make a big splash, and perhaps no more so than in its racy "Eliminator" trim, new for 1969. This is one such heady Mercury, dressed in sporty Competition Orange paint, and claimed to be an unrestored "survivor." Need it in your life? The '69 Mercury Cougar Eliminator recently popped up on eBay in Chepachet, Rhode Island . The genesis of the Mercury Cougar began in 1967, really with one singular purpose—to bridge the gap between the Ford Mustang and the Ford Thunderbird with a more upscale, stylish, and chiefly more "European" feeling pony car. It's safe to say the Cougar fit the bill. Using the Mustang chassis as a base, the early Cougars were about three inches longer than their 'Stang cousins and offered better legroom, sleek front and rear fascias, and a more luxe interior. Don't mistake "upscale" for "soft" however; come 1969 the Eliminator package gave the Cougar a seriously mean attitude. Spec-up the interior package and you received high-back bucket seats, a Rallye clock, wood-rimmed steering wheel, and padded interior moldings among other custom trims. Outside is where the Eliminator really struts its stuff, though. Eliminators came equipped with a blacked-out grille, special steel wheels, an aggressive front splitter and rear wing, plus racy decals and side stripes. Four color choices were available — Competition Orange, Bright Blue Metallic, White, and Bright Yellow. As standard, the '69 Mercury Cougar Eliminator came equipped with a 351 cubic inch V8, boasting 290 horsepower, as seen in the case of this car. More powerful options were also available, as noted by Barnfinds, which included a big 390 cubic inch V8 (320 hp), a high-revving Boss 302 V8, and the gargantuan 428 Cobra Jet V8. Peek beneath the body of this Cougar and the 351ci V8 is hooked up to a desirable close-ratio four-speed manual transmission, showing a claimed 35,243 miles. Though the mileage isn't verified, the car's overall condition and wear would suggest the readings to be true. Befitting those low miles, this unrestored Cougar does carry quite the high price — a tall $32,000.

NHTSA and Ford investigating steering issues in Crown Vic, Grand Marquis and Marauder

There may be more steering woes for the Ford Crown Victoria. The National Highway Traffic Safety Administration has opened a preliminary evaluation into the Crown Vic and Mercury Grand Marquis from the 2004 to 2007 model years and the Mercury Marauder for the 2004 and 2005 model years because the steering shaft can jam. The issue could potentially affect an estimated 500,000 vehicles.
According to the regulator, there is a possibility that the driver's side heat shield for the exhaust manifold can rust, dislodge, and then wedge into the steering shaft. If this occurs, it leads to a situation where the driver can no longer control the car.
NHTSA has received five complaints of this happening, including one alleged case with an injury. In that situation, the car was driving onto the highway, lost control and rolled over. One occupant was hurt in the accident.

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.