2021 Mercedes-benz Other on 2040-cars

Auto blog

Mercedes Concept IAA shows its mighty morphing aero aids

Modern supercars are utilizing more active aerodynamic elements that constantly adjust, to make them some of the fastest things on the road. The Mercedes-Benz Concept Intelligent Aerodynamic Automobile is using them too, but the know-how is applied here for ultimate efficiency rather than turning better lap times. In the standard design mode, the four-door luxury coupe looks like a CLS from the near future with styling that's mixed with a little of the F 015 concept. However at the press of a button or upon hitting about 50 miles per hour, the IAA transforms into aero mode to have an insanely low drag coefficent of just 0.19. To achieve the ultra-efficient shape, the rear of the concept stretches over 15 inches to guide air down the tail. Flaps in the bumpers also extend outward, and the wheels adjust to improve the flow around the sides. To trim things out underneath, a portion inside the front bumper moves, as well. Inside, passengers sit in organically shaped leather seats, but occupants have to look at a vast array of purple and blue LED accent lights. The big panoramic roof is a nice touch, though. It would be interesting to watch water tumble over this slippery shape when driving in the rain. To maximize efficiency, Mercedes powers the IAA with a plug-in hybrid that's hooked up to a gasoline engine. The result is 275 horsepower and an electronically limited top speed of 155 miles per hour. On the European testing cycle, the company figures the concept could cover 41 miles solely on electric power in aero mode. Showing the gains of the swoopy transformation, that figure falls to 38.5 miles in design mode.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...

Mercedes calling in CLS, E-Class over rubber seal fire risk

Mercedes-Benz has discovered a problem with certain E-Class and CLS-Class models and has notified the National Highway Traffic Safety Administration of a recall it's undertaking to resolve the issue. The problem is with the rubber seal at the back of the engine bay, which according to the statement below "may temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed." If it then comes into contact with the exhaust system, it could start a fire. And fires in the engine bay are never a good thing, unless they're contained entirely within the combustion chamber. The issue affects an estimated total of 147,224 E-Class and CLS-Class vehicles, all told, across America – including four-doors, wagons, hybrids and AMG performance models (but no E-Class coupes or convertibles) from the 2013-15 model years. To fix the problem, Benz dealers will simply need to attach four additional clips to keep the seal in place, and will start doing so midway through next month. RECALL Subject : Rubber Seal may Dislodge and Contact Exhaust Report Receipt Date: FEB 13, 2015 NHTSA Campaign Number: 15V088000 Component(s): STRUCTURE Potential Number of Units Affected: 147,224 Manufacturer: Mercedes-Benz USA, LLC. SUMMARY: Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 E350 Sedan, E350 4Matic Sedan, E350 4Matic Station Wagon, E400 Hybrid Sedan, CLS 550 CGI, and CLS550 4Matic, 2013-2014 E550 4Matic Sedan, 2013 E63 Sedan, E63 Station Wagon and CLS63, 2014-2015 CLS63 4Matic, E63 4Matic Sedan, E63 4Matic Sedan "S", and E63 4Matic Station Wagon, 2015 CLS400, 2015 E400 Sedan, E400 4Matic Sedan and CLS400 4Matic and 2014 CLS63 "S". The affected vehicles have a rubber seal at the back of the engine bay that may temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed. CONSEQUENCE: If the rubber seal falls into the engine compartment, it may contact parts of the exhaust system, increasing the risk of a fire. REMEDY: MBUSA will notify owners, and dealers will attach four additional retaining clips to the rubber seal, free of charge. The recall is expected to begin by mid-March 2015. Owners may contact MBUSA customer service at 1-201-573-5339. MBUSA's number for this recall is 2015020001. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.