2013 Mazda 6 I Touring Sedan 4-door 2.5l Engine Automatic Transmission 29k Miles on 2040-cars

Auto blog

Automakers drop support for Trump effort against California emissions

WASHINGTON — Toyota, Fiat Chrysler (now known as Stellantis following its merger with Peugeot) and other major automakers said on Tuesday they were joining General Motors in abandoning support for former President Donald Trump's effort to bar California from setting its own zero emission vehicle rules. The automakers, which also included Hyundai, Kia, Mitsubishi, Mazda and Subaru, said in a joint statement they were withdrawing from an ongoing legal challenge to California's emission-setting powers, "in a gesture of good faith and to find a constructive path forward" with President Joe Biden. The automakers, along with the National Automobile Dealers Association, said they were aligned "with the Biden administrationÂ’s goals to achieve year-over-year improvements in fuel economy standards." Nissan in December withdrew from the challenge after GM's decision in November shocked the industry and won praise from Biden. On Monday, the Justice Department asked the U.S. Appeals Court for the District of Columbia to put the California emissions litigation on hold to "ensure due respect for the prerogative of the executive branch to reconsider the policy decisions of a prior administration." Biden has directed agencies to quickly reconsider TrumpÂ’s 2019 decision to revoke CaliforniaÂ’s authority to set its own auto tailpipe emissions standards and require rising numbers of zero-emission vehicles, as well as Trump's national fuel economy rollback. Asked to respond to the automakers' action, White House climate adviser Gina McCarthy said in a statement that "after four years of putting us in reverse, it is time to restart and build a sustainable future, grow domestic manufacturing, and deliver clean cars for America." California Governor Gavin Newsom praised the automakers on Twitter for "dropping your climate-denying, air-polluting, Trump-era lawsuit against CA" and urged them to join the voluntary framework. TALKS WITH BIDEN Separately, an industry trade group on Tuesday proposed to start talks with Biden on revised fuel economy standards that would be higher than Trump-era standards but lower than ones set during the prior Democratic administration. The Trump administration in March finalized a rollback of U.S. Corporate Average Fuel Economy standards to require 1.5% annual increases in efficiency through 2026, well below the 5% yearly boosts under the Obama administration rules it discarded.

Mazda G-Vectoring Control makes driving better without you knowing

Mazda has just spent eight years developing a new technology that will make its new cars a lot more fun to drive, even if you have absolutely no idea that it's working. And subtlety's the point, Mazda engineers told us at a press event at Mazda Raceway Laguna Seca. In fact, the effects of what they've dubbed G-Vectoring Control are so fine that the marketing and PR teams are at a loss for how to do their jobs with it. "The engineers have done their work," said Mazda Director of Communications Jeremy Barnes, "But how do we get the message across?" The basic premise is this: G-Vectoring activates only when the car's on-board computer reads simultaneous steering and throttle input. The data — including throttle position, steering angle, and, crucially, how quickly you're adjusting the steering angle — are then funneled through an algorithm to reduce engine torque, which transfers vehicle weight, adding more grip to the wheels that need it. The system will appear first on 2017 Mazda6 sedans arriving in showrooms later this year, followed by the 2017 Mazda3. Actually, "subtle" does not even begin to describe the effect. G-Vectoring Control can detect as much as one tenth of one degree of steering angle, and changes the cornering forces only 0.1 to 0.5 g as a result. "That's less than the human body can feel," explained Vehicle Development Engineer Dave Coleman. In practice, G-Vectoring reduces the steering angle at turn-in, as well as the rate at which one turns the wheel. To demonstrate, Director of R&D Kelvin Hiraishi rode shotgun with us in a specially equipped Mazda6 that allowed him to turn G-Vectoring on or off at the push of a button (production cars will always have it on). Hiraishi had us drive a number of courses, including Mazda Raceway Laguna Seca itself, while an engineer measured our steering inputs with a laptop Matrix'd into the car's electronic brain. I drove the same course several times with the same car in the same conditions, with cruise control locked and the system turned on or off. Lo and behold, with G-Vectoring activated, the engineer's output graph showed that my steering inputs were indeed reduced ever so slightly. There were two times that G-Vectoring was markedly noticeable. The first on a turn with a minor banking toward the outside, and the second was during cornering over an artificially wet section of the course — in other words, when the car was at the limits of adhesion.

2018 Mazda6 Wagon: Beautiful but forbidden

Mazda has finally revealed the updated Mazda6 wagon it announced a few weeks ago. It's just as beautiful as we expected. The exterior features most of the same updates as the sedan version. They include a grille with more depth and dimension, a cleaner lower fascia, and headlights that are more integrated with the grille. Inside, the dashboard has been revised to look less cluttered, and the high-end leather and suede trimmings of the Signature trim are available. View 12 Photos Of course, the 2018 Mazda6 wagon still won't be available in America. And that's particularly disappointing, especially for this author, because the car looks so great. But we do understand the reasons why. Nobody buys wagons, at least without plastic body cladding on them. Plus, Mazda already offers the CX-5 here in the United States, and it serves effectively the same purpose, but in a much more popular crossover package. Seriously, the CX-5 is Mazda's best-seller over the last two months, selling more than twice as many as the next best-seller, the Mazda3. But there's still a silver lining to our lack of a wagon. You see, a close examination reveals that while the European Mazda6 sedan and wagon get most of the same updates as those in the American market, they won't get the 250-horsepower, 310 pound-feet of torque-producing turbocharged 2.5-liter gasoline engine we're getting. And given a choice, we would probably prefer more power than a wagon variant. The most potent engine over in Europe will remain the diesel 2.2-liter engine making 181 horsepower and 328 pound-feet of torque. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Related Gallery 2018 Mazda6 wagon View 30 Photos Image Credit: Live photos copyright 2018 Drew Phillips / Autoblog.com Geneva Motor Show Mazda Wagon 2018 Geneva Motor Show mazda6 wagon