2009 Sport Used 2l I4 16v Manual Rwd Convertible Premium on 2040-cars

Auto blog

Next Mazda MX-5 Miata to weigh a ton(ne), literally

Looking at recent spy shots of the fourth-generation Mazda Miata, it's obvious this sporty little roadster will grow in size compared to the current model, but it's also going on a diet. At the Tokyo Motor Show, Auto Motor und Sport sat down with Mazda executive Kiyoshi Fujiwara, who gave a little more insight into the Miata's redesign.
Fujiwara said that they're aiming for a curb weight of a tonne (metric ton), which is 1,000 kilograms or right around 2,200 pounds, for the next-generation Miata. This would make the roadster at least 300 pounds lighter than the current NC Miata, but still about 200 pounds heavier than the original NA.
There is no indication as to how Mazda will go about removing that much weight from the bigger car, but with as popular as the power retractable hard top (PHRT) model is on the current car, the new Miata may ditch this feature to lose its weight. Improving the power-to-weight ratio appears to be a key goal of the Mazda team, so we also wouldn't be surprised to see a more powerful engine underneath the longer hood.

2014 Mazda CX-5 with 2.5-liter Skyactiv engine

Back in October, we compared the relative merits of two new and very good small crossovers: the 2013 Ford Escape and 2013 Mazda CX-5. The CX-5 we tested then had Mazda's 2.0-liter Skyactiv-G engine under its hood, and it managed to just edge out the EcoBoosted Ford despite being down by some 23 horsepower and 34 pound-feet of torque. Had it been available, the 2.5-liter Skyactiv engine that we recently had the opportunity to try out in the 2014 Mazda CX-5, it may have made that comparison even easier to call in the Japanese CUV's favor.
Clearly, if you're in the market for a reasonably sized crossover, the CX-5 should, at the very least, be on your test-drive list. The new engine offering will let buyers opt for a stronger powerplant, with 184 hp and 185 lb-ft on tap. On our second day in Austin's Hill Country - the first was spent quick-spinning the 2014 Mazda6 i Sport, you'll recall - we covered a couple of hundred miles and put the new CX-5 through its paces; here's what we turned up.
Driving Notes

Tougher than steel: Wood pulp could make lighter auto parts

KYOTO, Japan — The global push among carmakers to make ever lighter vehicles is leading some auto suppliers in Japan to turn to what seems like an unlikely steel substitute — wood pulp. Japanese researchers and auto component makers say a material made from wood pulp weighs just one-fifth of steel and can be five times stronger. The material - cellulose nanofibers — could become a viable alternative to steel in the decades ahead, they say, although it faces competition from carbon-based materials, and remains a long way from being commercially viable.> Related: Jay Leno drives the Renew cannabis car — hemp you can't dent Reducing the weight of a vehicle will be critical as manufacturers move to bring electric cars into the mainstream. Batteries are an expensive but vital component, so a reduction in car weight will mean fewer batteries will be needed to power the vehicle, saving on costs. "Lightweighting is a constant issue for us," said Masanori Matsushiro, a project manager overseeing body design at Toyota. "But we also have to resolve the issue of high manufacturing costs before we see an increased use of new, lighter-weight materials in mass-volume cars."A NEW PROCESS Researchers at Kyoto University and major parts suppliers such as Denso Corp, Toyota's biggest supplier, and DaikyoNishikawa Corp, are working with plastics incorporated with cellulose nanofibers — made by breaking down wood pulp fibers into several hundredths of a micron (one thousandth of a millimeter). Cellulose nanofibers have been used in a variety of products ranging from ink to transparent displays, but their potential use in cars has been enabled by the "Kyoto Process," under which chemically treated wood fibers are kneaded into plastics while simultaneously being broken down into nanofibers, slashing the cost of production to roughly one-fifth that of other processes. "This is the lowest-cost, highest-performance application for cellulose nanofibers, and that's why we're focusing on its use in auto and aircraft parts," Kyoto University Professor Hiroaki Yano, who is leading the research, told Reuters in an interview. The university, along with auto parts suppliers, are currently developing a prototype car using cellulose nanofiber-based parts to be completed in 2020.