1992 Mazda Miata Convertible 2-door 1.6l on 2040-cars

Auto blog

Flyin' Miata is building a V8-powered MX-5 ND

It's cold in many parts of the country, but this V8-swapped 2016 Mazda MX-5 Miata that Flyin' Miata is developing has us dreaming about throwing on a parka and taking a very brisk drive. This beast is the product of the talented folks at Flyin' Miata, but we can't get too excited just yet. According to the company's brief Facebook post, this is just a dummy V8, placed under the Miata's hood to confirm fit. Judging by the photo, the engine fits like a glove. "There's still a long way to go before this is a real thing," Flyin' Miata writes, but the company admits everything looks "very promising" so far. The post doesn't mention any details about the estimated specs, but Autoblog reached out to Flyin' Miata for more information about this intriguing build. Keith Tanner, one of the mad scientists who shoehorns V8s into Miatas at the Colorado outfit, told us that Flyin' Miata is looking at both the LS3, which will provide between 430 and 525 hp, and the LT1 which is 460 hp out of the box. A supercharged LT4 is also being considered, but as Tanner put it, "that might be a little nuts" in a car as light as the ND. In any of these engine configurations, Tanner estimates the V8-swapped ND should comfortably be a sub-4 second to 60 mph car. The transmission will be a Tremec T56 Magnum six-speed manual. The suspension, brakes, fuel system, cooling system, and the chassis itself will all be beefed up to handle the power, as per normal FM practice. The one question mark is the rear end, as the ND's existing one simply won't be up to the task of putting that much horsepower to the ground. The 2016 Miata was one of the best cars we drove in 2015, but Flyin' Miata knows how to turn a standard MX-5 into an absolute hotrod with the company's LS3 V8 conversions for earlier models. Imagining the more modern chassis from the latest generation with a massive dollop of more power is an exciting thought. We can't wait to see how this project turns out. Related Video:

Mazda CX-5 Luggage Test | How much cargo space?

We're already seen how Mazda's largest crossover, the CX-9, does at stuffing luggage inside its cargo hold. Now it's time for the next rung down the Mazda ladder. The Mazda CX-5 has 30.9 cubic-feet of space behind its raised back seat, which on paper, is considerably less than its top competition. The Hyundai Tucson leads the way with 38.7 cubic-feet, the Honda CR-V (39.2) and Toyota RAV4 (37.5) are basically the same, and the Subaru Forester has between 33 and 35 depending on options. However, the CX-5 does have more than the Chevrolet Equinox (29.9), Jeep Compass (27.2) and Ford Escape when its sliding back seat is in its aft-most position (33.5 when all the way forward).  Basically, this compact Mazda's cargo area is midpack, which makes it a good choice for my first luggage test of the segment. Let's see how much of the luggage in my garage fits inside. As a refresher, I use two mid-size roller suitcases that would need to be checked in at the airport (26 inches long, 16 wide, 11 deep), two roll-aboard suitcases that just barely fit in the overhead (24L x 15W x 10D), and one smaller roll-aboard that fits easily (23L x 15W x 10D). I also include my wife's fancy overnight bag just to spruce things up a bit (21L x 12W x 12D).  I started by keeping the cargo cover in place to see how much fits underneath it. The answer is the four largest bags. The two smaller ones did not. OK, now let's remove the cargo cover, which is an unusual design. Rather than a roller-type cartridge that you manually pull into place or a rigid hatchback-like unit that rises up when the liftgate goes up, the CX-5 basically combines the two. The forward bit is attached to the liftgate and unspools when opened.  To detach it, you need to unfasten these plastic clamps and then remove the cartridge reel much as you would a normal cargo cover. OK, and now here's how much the CX-5 can fit with the cargo cover removed.  All of it! That above configuration is just the first thing I came up with, but there's likely additional Tetris formations to be found. Note that the tailgate does close here but the middle cases' wheels are awfully close to the window.  I'm not going to stop there, though. I went ahead and rummaged through my garage to see what it would take to fill'er up. There you go: one duffle bag and one gym bag stuffed into the spaces. You could probably fit a grocery bag right in front there, too.

Mazda still has a team working on rotary engines

The flame still burns within Mazda to stage a rotary engine revival. Before you start getting excited, it's way too soon to start saving money for the fabled, next-gen RX-7 or RX-8. Still, company boss Masamichi Kogai confirmed to Autocar that the Japanese automaker has an engineering team dedicated to improving the Wankel. This development group has the hard task of trying to make the rotary stack up to modern internal combustion engines in terms of emissions and fuel-economy standards. Neither factor were ever exactly Wankel's strong suits. Kogai described them as working "very enthusiastically" to Autocar. The boss didn't discuss any future RX-vehicles or the size of the team, however, a report from last year indicated that there were 30 engineers in partnership with universities to update the engine's design. After problems keeping up with emissions and fuel economy, Mazda built it's last rotary for an RX-8 in June 2012. Since then, there have been intermittent rumors of a return. One possible solution was a design called the 16X that was supposed to offer more torque and better fuel economy. Another possibility was a small-displacement unit as a range-extender in an electric Mazda2. Rumors of a new RX-7 have been heard for years. In 2013, Kogai clearly said that it wasn't happening. When asked again last year, he reiterated the same point.