1992 Mazda Miata Base Convertible 2-door 1.6l on 2040-cars

Auto blog

Mazda MX-5 Miata to spawn coupe, Mazda6 to get quick successive updates

Despite the PRHT's availability, some are still yearning for a proper fixed-head coupe.
We are just days away from the official unveiling of the next-generation 2016 Mazda MX-5 Miata on September 3, and it's fair to say that the mouths of enthusiasts are watering in anticipation for the latest version of this iconic roadster. Hard facts about the new droptop aren't easy to find, and in the absence of further disclosure from Mazda officials, the rumormill is in full swing, including word that a long-awaited hardtop coupe model will figure into the new generation's plans.

Confirmed: Mazda Miata gets more power, higher redline, telescoping wheel

Our friend over at Road & Track, Bozi Tatarevic, has a keen nose for stuff just like today's Miata news, and he spotted an article by the Japanese car magazine Car Watch that details Mazda's upcoming updates. Car Watch actually got to drive the car, too. There's a lot to go through, but the highlight has to be confirmation of what we told you earlier this year about a significant power bump: The Miata will indeed get an increase of 26 horsepower, from 155 to 181. But the power's not the whole story. Mazda has increased the redline from 6,800 RPM to 7,500. It's not clear at this point where torque and power peaks are in the rev range, or how these changes affect low-speed drivability, but more revs are almost always a good thing and aren't likely to detract from the roadster's fundamental goodness. Car Watch reports that lighter pistons and connecting rods are fitted to help reduce rotational mass in the 2.0-liter inline-four. Some valvetrain changes were needed to support the higher redline, mainly stiffer valvesprings to prevent valve float. Mazda also changed the shape of the valves and optimized the intake ports to breathe better at higher RPM. The inner diameter of the exhaust ports were increased to flow better through a new muffler better tuned to the engine's new operating range. This confirms and gives a little more detail to what we reported earlier based on a leaked document from Mazda Canada. Car Watch also confirms that the revised Miata will get a low-inertia dual-mass flywheel, which should help absorb some vibration, noise and harshness from the higher-revving engine without losing too much of the directness that a single-mass flywheel provides. Mazda usually gets stuff like this right, so while we won't know until we get a chance to drive it whether the DMF feels "right," we're not too worried about it. There's also a telescopic steering wheel, a first in any Miata, which has a range of about 1.1 inches. That doesn't sound like much, but it should help folks with longer legs reach the wheel without having to crank the seat forward. Interestingly, Car Watch reports that the telescoping wheel was opposed by some in the company seeking to save every fraction of an ounce of weight, and to get it through, the company apparently had to change some of the material in the upper steering column from steel to aluminum to satisfy the weight-conscious. Little details like these are fantastic.

Mazda Miata speedster and spyder concepts set for SEMA

Mazda will show speedster and spyder concepts based on the 2016 MX-5 Miata next week at SEMA in Las Vegas. The speedster is at the top of the teaser, and the spyder is the bottom half. The speedster goes with an extreme lightweight design. It has only a small wind deflector in place of the windshield and a blue ether topcoat. The spyder is a vintage roadster rendered into a modern form with a handcrafted leather interior and mercury silver paint job. Both are lighter than the production version and will be sure to get the hearts of Mazda fanatics and roadster enthusiasts alike racing at the possibilities. We doubt either will actually see production, like so many Miata-based concepts of the recent past. But that won't stop us from dreaming all the same. MAZDA TO SHOWCASE LIGHTWEIGHT PERFORMANCE AT SEMA WITH TWO MX-5 MIATA CONCEPTS - MX-5 Spyder and Speedster Concepts Bring Vintage Cues into Modern Designs - IRVINE, Calif., Oct. 29, 2015 -- The Mazda MX-5 Miata has been an exercise in honing the concept of a lightweight sports car for more than 26 years, created solely for driving exhilaration. But for the 2015 SEMA Show at the Las Vegas Convention Center, Mazda designers wanted to see what they could do if that idea was taken to the extreme. What they created were two vastly different takes on the fourth-generation MX-5: The 2016 MX-5 Spyder Concept and 2016 MX-5 Speedster Concept. MX-5 Spyder captures the character of a vintage roadster and translates it into a modern-day design, including bespoke leather interior details that were painstakingly crafted, and featuring a new Mercury Silver concept paint color. MX-5 Speedster is a study in the extremes of lightweight, purpose-built performance, paying homage to minimalist roadsters of the 1950s. The Blue Ether-painted MX-5 Speedster is uncompromised in its approach to wind-in-the-hair driving, going so far as to eschew a traditional windshield for a lighter deflector. Both cars are significantly lighter than the 2,332-lbs. MX-5 roadster that customers can purchase at dealers and come with a host of conceptual and aftermarket pieces and fabrication from partners including Racing Beat, Haartz Corporation, ASC – American Sunroof Corporation, Makin Industries/RAYS Wheels, KW Suspensions, Delta Seat, H&R Springs, Lusch, AC&A Manufacturing, Franks Fab Shop, Long Road Racing and SIM Specialty Interior Manufacturing.