2011 Mazda Cx-9 Grand Touring on 2040-cars

Auto blog

2019 Mazda 3 recalled because the wheels could fall off while driving

Here’s a recall we had to read twice before believing. Mazda is bringing in 25,003 Mazda 3s that just rolled off the assembly line, because the wheels may fall off while driving. All the Mazda 3s are 2019 model year cars, so itÂ’s only the totally new generation Mazda 3 under the gun here. Thankfully, Mazda says there are no cases of this occurring to owners, and therefore no injuries or deaths related to the issue. As for the cause of the wheel detachment? Mazda put out a statement explaining the issue at hand.  “A manufacturing process error may result in a gap between the wheel hub bolt and hub flange during assembly. This gap causes loosening of the lug nuts though they were initially tightened to the correct specification at the plant. A rattling noise occurs prior to a wheel detachment from the vehicle,” Mazda says. ItÂ’s heartening to see Mazda did in fact tighten the lugs at the factory, but still extremely troubling to see that they can loosen all on their own. Our advice? Walk on out to your shiny, new Mazda 3 and torque those lugs to spec. If you donÂ’t have a torque wrench, then just use the wrench that came with the car to make sure theyÂ’re not loose. Those that have a new Mazda 3 should be on the lookout for a recall notice in the mail. YouÂ’ll then be able to take the car to the dealer for Mazda to fix the problem. Until then, just keep an eye on your lugs. A wheel flying off while driving at speed is always a recipe for disaster, and we sure do enjoy driving the new Mazda 3 at speed.

Mazda Furai concept designer talks about his car's passing

Last week, there was mourning at the Autoblog offices as word trickled in that the Mazda Furai concept - one of the coolest, best-looking showcars to grace an auto show stage since the wild and crazy 1960s -had been killed. It was killed on the track with the folks from Top Gear in attendance. We're sure the gods of driving would have wanted it to die on a circuit, but that doesn't make its fiery passing any easier to deal with.
The Furai is the rare concept car that had a lasting appeal with enthusiasts, partly because it was a real, functioning racecar, complete with a wacky three-rotor Wankel engine and cutting-edge Nagare design. Now that it's gone, though, Road & Track's Mallory McMorrow, who was an intern at Mazda Design when the Furai was being styled in 2007, has published an interview with one of the men who penned the Mazda showcar's striking exterior, Carlos Salaff. It's a great piece on the emotional connection between a designer and his creation, and one you should take the time to read. Click on over to R&T for the full story.

Crossovers help Mazda post its best January sales in 24 years

Mazda's 2017 ended on a bit of a flat note. It wrapped up the year with 2.8 percent fewer U.S. sales than 2016, and 8 of the 12 months lower month-over-month. But 2018 is off to a much brighter start with the company having its best January sales month since 1994, with just under 25,000 cars sold. Besides that headline statistic, the higher sales also mean this January exceeded 2017's sales by 15 percent or about 3,300 cars and put it ahead of January in that healthy 2016 year. Compared with this past December, though, sales are down about 2,000 cars. The gains are entirely due to the success of Mazda's crossover SUVs. The CX-5 was the best of the best with a month-over-month gain of over 66 percent. In actual numbers it sold about 13,500 copies compared with about 8,000 last January. The big three-row CX-9 had a big jump going from 1,600 units sold last January to about 2,300 for a gain of almost 47 percent. Even the little CX-3 saw a small gain between the two Januarys, going from about 1,200 to 1,350 sales. View 14 Photos Mazda's January would've been even better if its conventional cars hadn't dropped so much. Both Mazda Miata and Mazda6 sales dropped by just over half. The Mazda dropped from 3,300 sales to just under 1,600, and the Miata dropped from a little over 900 to a little over 400. Mazda3 held on a little better with just a 12 percent drop from last January going from about 6,600 to 5,800 sales. The lopsidedness of these sales isn't all that surprising. Crossovers have been a boon to loads of manufacturers. For example, Mitsubishi had an 2017 full of sales improvements, with the company finally breaking 100,000 units for the first time in years, and it was all because of improving crossover sales. January's sales also continue an unfortunate downward trend for Mazda's cars, with both the Mazda6 and Mazda3 having month-over-month declines every single month since February. It will be interesting to see if the new turbocharged engine option on the Mazda6 will improve sales of the sedan later this year. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.