2015 Mazda Cx-5 Touring on 2040-cars

Auto blog

Mazda recalling 190,000 CX-7s due to rusty ball joints

UPDATE: This post has been updated with additional information from Mazda. The Basics: Mazda is recalling 190,102 Mazda CX-7 crossovers built between February 14, 2006, to May 9, 2012 – model years 2007 through 2012. The Problem: Water can sneak in between the suspension ball joint fittings. If snow and road salt are common in your neck of the woods, the joints can corrode and separate from the lower control arms. That's bad if you enjoy steering your CX-7. According to Mazda, owners of affected models may notice a rattle from the front suspension due to the loose ball joint in the lower control arm fitting. Mazda describes separation of the ball joint and control arm as a "worst case" scenario "after extended operation in such condition." Injuries/Deaths: It's unknown if the rusting issue has led to any crashes, injuries, or deaths. Autoblog has a call into Mazda for additional details and will update this post with any new information. There have been no reports of accidents, injuries, or fatalities related to this recall. The Fix: Owners should report to their local Mazda service center, where techs will replace the both front lower control arms. Any work done is free of charge. If you own one: Mazda will perform some automotive triage with this recall, focusing on CX-7s that have had the longest exposure to salt and are most likely to suffer control arm separation first. Owners of 2007s and 2008s come first, followed by 2009 through 2011 models. Mazda will also focus on vehicles registered in states where snow and road salt are most common – Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin, and Washington, D.C. If you live in a more temperate region or own a 2012 CX-7, Mazda will perform recall work as "parts are available." Owners can contact Mazda customer service at 1-800-222-5500 for additional info. Recall notices should hit the mail around October 10th. Related Video: Featured Gallery 2011 Mazda CX-7: Review View 21 Photos News Source: NHTSAImage Credit: Copyright 2016 AOL Recalls Mazda Crossover mazda cx-7

Mazda Skyactiv-X Review | The revolution begins with a squeeze-bang

The matte black Skyactiv-X prototype looks like a rough Mazda3, perhaps reconstructed after a bad wreck by an over-enthusiastic owner of a spot welder and lots of gaffers' tape. Ribbed ducts poke out of the dash sending two breaths of conditioned air to no one in particular. Even its revolutionary engine, the thing we're here to experience, is entombed in a massive, nondescript cover to mask its unseemly noises. It's a wild, strange way to meet a very unconventional vehicle that promises diesel-like fuel economy, a wide torque band, and an exotic method for burning less gas than ever before. It takes a few hours for Mazda's engineers to explain the fundamental principles of operation. For more detail, read our Skyactiv-X Spark Controlled Compression Ignition explainer, but here's a very brief overview. Skyactiv-X marries some traditional gasoline engine characteristics with a novel form of compression ignition called SPCCI. The key for Skyactiv-X is to use very high compression in the cylinder and an extremely lean fuel-air mixture. Squeezed right to the cusp of getting hot enough to blow up all on its own (which is very hard to predict), a squirt of extra gas and a spark interject to cross that compression-ignition threshold in a controlled and predictable manner. See the animation below: That takes a few essential components to get just right. One is a massive amount of computer processing power and some pressure sensors in the individual cylinders, because the ambient conditions change how and when these things happen. Skyactiv-X uses a clutched supercharger to pump in additional air when needed to nail the mixture precisely, and high-pressure injectors to get the low ratios of fuel to disperse properly in the chamber. And since it operates like a conventional gasoline engine sometimes, it uses valve timing to lower the very high compression ratio so it doesn't reach combustion ignition in that mode. In practice, the Skyactiv-X runs in compression ignition mode most of the time. In practical terms, that means it drives like a torquey gasoline Skyactiv engine. The torque curve is broad and flat — diesel-like in that respect. That also means it can get away with using a six-speed transmission and a lower final drive for better response. There's enough grunt and economy together that Mazda can let the engine spin faster — at 60 mph, it's running at roughly 1,000 more RPM than a similar gas engine, with greater efficiency.

Ever wonder how to really pronounce Japanese automaker names?

People tend to get very set in their ways when it comes to the pronunciation of words. Just look at the endless debates over whether or not to say the final 'e' in Porsche (which you should in terms of correct German enunciation). Or the argument about whether to follow the British convention and give the 'u' in Jaguar a special delivery or to say the 'ua' diphthong as more of a 'w' sound, as usually happens in the US.
This short video doesn't answer either of those automotive questions, but it does allow a native Japanese speaker to demonstrate the accepted pronunciations for several, major automakers from the country. One benefit is that it clears up the occasional debate over whether Nissan should be said with a long or short 'i' sound. Also, listen closely to how the female host says Mazda as Matsuda, the way it's actually said in the language. Even if this doesn't change the way you enunciate these brands, at least now you know the accurate way in Japanese.