2007 Lexus on 2040-cars

Auto blog

Why is there a huge bulge in 2021 Lexus IS 300 AWD's driver footwell? We explain

After an initial turn a few weeks ago for the 2021 Lexus IS first drive review, the revised luxury sedan has returned to the Autoblog garage for a second look. This middle-of-the-road IS 300 AWD pairs a 260-horsepower V6 with a six-speed automatic transmission and four driven wheels, and frankly it's the least interesting way to spec out the redesigned sedan. While there are cars in this segment designed to get a performance boost from their all-wheel-drive systems even in dry conditions, the IS isn't one of them. Adding insult to injury, you get stuck with a cramped driver-side footwell care of the engineering shenanigans that went into making this system possible.  While we've mentioned this particular compromise before, we rarely touch on the reasons why it exists in the first place. The fundamentals are fairly obvious; the standard IS utilizes a longitudinal, rear-wheel-drive powertrain. As is typical with this configuration, the transmission sits in a tunnel beneath the center console. This arrangement works just fine, provided you don't need to power the front wheels.  To do so in a traditional car like the IS requires a literal end-around maneuver involving the engine and transmission, which we've diagrammed for you below care of MSPaint. This is a bit simplified for the sake of this write-up, and it should be noted that this is not the only way to implement AWD in an inherently RWD platform, but it illustrates how the power for the front axle (red) and rear axle (blue) flows from the transmission to the drive wheels. To get juice flowing to the front axle, Lexus had to add a parallel output shaft, exiting the transmission from the front with enough clearance for the bell housing and engine, which sits between the transmission and the front differential. This requires quite a bit of lateral reach, meaning the housing has to extend much farther out than usual to accommodate it (yellow arrow). As a result, the all-wheel-drive transmission looks a lot like a sci-fi gun with a chunky drum magazine hanging off the side of it. The hump (above right) in the footwell is there to clear this protrusion. This basic configuration isn't unique to Lexus. In fact, if you look at a BMW xDrive cutaway, it's similar. So, why no "hump" in other cars? There are multiple factors, but to boil it down to what is most relevant, it's a combination of the resulting shape of the Lexus transmission housing and the size of the IS chassis.

Lexus GS F coming in 2016 with 500 hp

The Lexus GS F has been one of those cars that's been rumored and whispered about for years, but has never come to fruition. The last time we spoke of the Lexus-badged BMW M5-killer was in a crop of spy photos, posted one year ago yesterday. So what's behind this latest rekindled round of rumors?
Well, according to Autocar, sources have claimed that the GS F will hit markets in 2016, and that it will make use of a more potent version of the Lexus RC F's 5.0-liter V8 that will sing to the tune of 500 horsepower and 400 pound-feet of torque. An eight-speed automatic transmission from ZF will be included, as will a Torsen limited-slip diff. Taken as a whole, the executive sedan should get to 60 in the mid-four-second range and accelerate to a top speed of 170 miles per hour.
Prices in the UK will start at 80,000 pounds ($130,000 at today's rates, but as we know, translating British prices to American prices is an inexact science), and right away, we run into a big issue.

Toyota recalls 370k Sienna minivans, 10.5k Lexus GS models over separate issues

The year of the recall continues, but this time it isn't from General Motors. Toyota is announcing two, separate recalls affecting a pair of its models.
First, Toyota is recalling 370,000 Sienna minivans from the 2004 to 2011 model years that are registered or originally sold in cold-weather states. The problem is that the spare tire carrier assembly cable can be splashed by water contaminated with road salt and cause corrosion. There is a splashguard in place to prevent this, but it sometimes gets lost in "normal usage," according to the company. If the cable does break, then "the spare tire may separate from the vehicle."
This is actually the second repair for this problem for some of these vehicles. In 2010, Toyota issued a recall on 600,000 Siennas from the 1998 to 2010 model years. At the time, it installed a new splashguard and sprayed the area with an anti-rust chemical. However, according to Toyota spokesperson John Hanson speaking to Autoblog, the campaign worked for the 1998 to 2003 models but wasn't sufficient for the newer ones. For the latest recall, the vehicles are getting the entire cable replaced with a stainless steel unit and a new splashguard.