2012 Lexus Is 250 on 2040-cars

Auto blog

Why is there a huge bulge in 2021 Lexus IS 300 AWD's driver footwell? We explain

After an initial turn a few weeks ago for the 2021 Lexus IS first drive review, the revised luxury sedan has returned to the Autoblog garage for a second look. This middle-of-the-road IS 300 AWD pairs a 260-horsepower V6 with a six-speed automatic transmission and four driven wheels, and frankly it's the least interesting way to spec out the redesigned sedan. While there are cars in this segment designed to get a performance boost from their all-wheel-drive systems even in dry conditions, the IS isn't one of them. Adding insult to injury, you get stuck with a cramped driver-side footwell care of the engineering shenanigans that went into making this system possible.  While we've mentioned this particular compromise before, we rarely touch on the reasons why it exists in the first place. The fundamentals are fairly obvious; the standard IS utilizes a longitudinal, rear-wheel-drive powertrain. As is typical with this configuration, the transmission sits in a tunnel beneath the center console. This arrangement works just fine, provided you don't need to power the front wheels.  To do so in a traditional car like the IS requires a literal end-around maneuver involving the engine and transmission, which we've diagrammed for you below care of MSPaint. This is a bit simplified for the sake of this write-up, and it should be noted that this is not the only way to implement AWD in an inherently RWD platform, but it illustrates how the power for the front axle (red) and rear axle (blue) flows from the transmission to the drive wheels. To get juice flowing to the front axle, Lexus had to add a parallel output shaft, exiting the transmission from the front with enough clearance for the bell housing and engine, which sits between the transmission and the front differential. This requires quite a bit of lateral reach, meaning the housing has to extend much farther out than usual to accommodate it (yellow arrow). As a result, the all-wheel-drive transmission looks a lot like a sci-fi gun with a chunky drum magazine hanging off the side of it. The hump (above right) in the footwell is there to clear this protrusion. This basic configuration isn't unique to Lexus. In fact, if you look at a BMW xDrive cutaway, it's similar. So, why no "hump" in other cars? There are multiple factors, but to boil it down to what is most relevant, it's a combination of the resulting shape of the Lexus transmission housing and the size of the IS chassis.

Lexus NX begins production in Japan [w/videos]

Lexus entered new territory this past April when it revealed the new NX compact luxury crossover at the Beijing Motor Show, but it wasn't until now that the Toyota luxury division actually started building them. The first production examples started rolling off the assembly line last week at the Miyata plant in Japan, with the accompanying turbo engines built at the adjacent Kanda plant.
The arrival of the NX marks both the first time that Lexus has produced a compact crossover - an increasingly important segment for luxury automakers - and the first time Lexus has offered a turbocharged engine, one of two options alongside the hybrid version. The NX builds on two previous competences exhibited by Toyota: one is the RAV4, which pioneered the compact crossover segment back in 1994, the other being the Lexus RX that was among the first luxury crossovers when it arrived in '97.
Lexus reports that it has already taken some 6,500 pre-orders in Japan alone, with many more coming in from markets around the world - including ours, where it is sure to be a key player for the Japanese automaker alongside the hot-selling RX. Watch the videos below to see the NX starting its production run in Japan.

Lexus really put the spindle grille on its imaginary 'Men in Black' jet

There is a large constituency of people who do not like — hate, even — Lexus' signature spindle grille. But Lexus likes it, A LOT. So much so, that the company included the spindle design into its newest conceptual design study, the Lexus QZ 618 Galactic Enforcer Jet that will appear in "Men in Black: International." The two official trailers for the upcoming MIB reboot revealed that Lexus had a hand in the films. In the second, we even see a Lexus RC F transforming into an aircraft, a call back to Will Smith's and Tommy Lee Jones' flying car in the original. But this is the first full look at the fictional vehicle, which will be used by Tessa Thompson and Chris Hemsworth. Lexus had some fun with this and put out a press release detailing all of the Galactic Enforcer Jet's features. Lexus says it wears Umbra Black, the darkest black in the entire universe, and uses Hybrid Transformer Technology. Its Quasar Power Source2 Technology was secured through a secret alien knowledge swap and uses power from the closest Active Galactic Nucleus3 for universal travel. The propulsion system is named after Black Hole TON 618. The stats on this machine are pretty impressive. It gets 122 millennia per gallon, does zero to 60 in 0.0000000000001 nanoseconds, and has light-speed-matching capabilities. Drivers sit in intergalactically sourced and ethically spawned Adorian leather and have the choice of three drive modes: EcoDrive, SportDrive, and QuantumDrive. Further convenience and safety features include Amazon Alexa (which understands seven trillion alien languages), infinite scaling technology, gamma ray headlamps, an Inter-Galactic Positioning System, transforming seats with a 31-point safety harness, and the Lexus Safety System + with force field technology. In regards to styling, the jet has the Enforcer Package and can be ordered in six other colors. Check out the jet in action in "Men in Black: International" on June 14. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.