J03326 New Jeep Limited White Suv 4dr 3.6l V6 24v Automatic 4wd on 2040-cars

Auto blog

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.

Jeep Wrangler diesel likely after 2015 model refresh

We automotive journalists aren't always the right people to ask about whether a US-spec vehicle should or should not be offered with a diesel powertrain (hint: the answer is usually "YES"). But when it comes to the iconic, off-road-ready Jeep Wrangler, we aren't the only ones who have been clamoring for an oil-burning engine behind that famous seven-slat grille. To that end, it appears there's good news on the horizon, as Jeep CEO Mike Manley recently told Ward's Auto that the "Wrangler is on the radar to get (a) diesel."
"I'm confident that the Grand Cherokee will show just how large a demand there is for diesel, and I think what that will do is reinforce the need for us to target Wrangler as a vehicle that can take a diesel," Manley told Ward's. The most rugged of Jeeps is scheduled to get an overhaul around 2015-16, and the diesel powertrain will likely be introduced around that time.
This year alone, Chrysler will be adding a diesel engine to the Grand Cherokee SUV, as well as the Ram 1500 pickup and Promaster utility van.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.