Police Pkg Former Search And Rescue Excellent Cond. 1 Owner Always Maintained on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Chrysler readying 20 Moparized vehicles for SEMA

The Las Vegas Convention Center has plenty of space for aftermarket companies and automakers to show off their wares, and it looks like Chrysler is taking advantage of the spacious floor plan. At next month's SEMA Show, Chrysler will have a full 20 cars from its six brands decked out with Mopar gear.
As a hint of what is to come, Chrysler released a handful of teaser sketches showing glimpses of modified Jeep Cherokee, Ram 1500, Fiat 500L and Chrysler 300 concept vehicles. The automaker will also use the venue to show off a new line of Jeep Performance Parts offered by the all-new Mopar Off-Road Division. In addition to the images, Chrysler also issued a brief press release - posted below - breaking down some of the "industry-first features" that Mopar has offered in recent years.

Last Jeep Wrangler JK rolls off the line in Toledo

Say goodbye to the Jeep Wrangler JK. After more than 2.1 million models made since production began in 2006, a white 2018 Wrangler JK Rubicon Unlimited rolled off the line Friday at FCA's plant in Toledo, Ohio, as the last of its kind and as factory employees snapped photos. Fiat Chrysler is planning to retool the U.S. Toledo Supplier Park plant for an all-new Jeep pickup truck for launch in the first half of 2019. The final Wrangler JK will become one of the Jeep brand's show properties. "We take great pride in the role we have played in the history of this vehicle and the impact it has made in the Toledo community," Chuck Padden, the Toledo Assembly Complex manager, said in a statement. "We look forward to bringing that same commitment to the all-new Jeep truck." The JK has been on the road since 2007 and was built as part of a co-location concept with suppliers Kuka and Hyundai Mobis, which managed the manufacturing processes of the body and chassis, respectively. They'll also oversee those same responsibilties with the forthcoming Wrangler pickup, which is expected to begin production in the fourth quarter and hit showrooms in April 2019. We've been limited to spy shots of heavily camouflaged versions of that vehicle, which is tentatively called the Scrambler, though there were those ostensibly well-educated renderings from the Jeep Scrambler Forum a few weeks ago. FCA Chief Executive Sergio Marchionne has said he expects the new pickup to sell around 100,000 units per year, and the Toledo plant has an annual capacity of about 300,000 units. Meanwhile, FCA is continuing production of the Wrangler through the new Wrangler JL, which is being built on the north side of the Toledo Assembly Complex as part of a $4.5 billion production realignment to boost the Jeep and Ram brands. The Wrangler JL gets a 3.6-liter V6 that makes 285 horsepower and 260 pound-feet of torque. It's also available with a 2.0-liter turbocharged four-cylinder, which generates 268 hp and 295 lb-ft of torque, available only with an eight-speed automatic transmission, for an extra $3,000 (technically it's $1,000 for the four-cylinder engine and $2,000 extra for the eight-speed trans). A 3.0-liter diesel version is also due of the four-door version in 2019. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Image Credit: FCA Jeep Truck SUV Off-Road Vehicles FCA jeep wrangler jl