1970 Cj5 Jeep Fuel Injected Ram Jet 350. Arb Lockers With Onboard Compressor on 2040-cars

Auto blog

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.

Jeep Cherokee Trail Carver is a more rugged Trailhawk

We briefly mentioned the Jeep Cherokee Trail Carver that was heading to SEMA last week when discussing the Mopar lineup set to be shown in Las Vegas. At the time, though, we weren't able to dive too deeply into details. But with SEMA in full swing, we were able to sneak over and grab some snaps of one of the first modified Cherokees we've seen. The Cherokee is, after all, kind of an unknown quantity in the modification department, being so new and featuring such a polarizing design. We were quite interested to see what Mopar could come up with.
Starting with the Trailhawk 4x4 and its 3.2-liter V6, the engine is fitted with a Mopar cold-air intake and a new exhaust, although it's not clear what sort of power boost has resulted. We'll admit, we were hoping Jeep and Mopar would get a bit more aggressive with the Cherokee's suspension (has anyone thrown a few-inch lift on the new Jeep yet?), but there's no mention of upgrades beyond the knobby, off-road tires. Those should do some good when the going gets rough, while rock rails are there to protect the Auburn Pearl paint on the body.
Speaking of that paint, it's complemented by an interesting graphics package in contrasting black and Crush Orange. The cabin sports Katzkin Amaretto leather seats, along with tech-friendly items like a wireless charging system for cellphones and wireless internet.

2018 Jeep Wrangler will have an aluminum hood and doors, leaked memo says

Earlier this year, FCA CEO Sergio Marchionne revealed that 2018 Jeep Wrangler would feature a heavy dose of aluminum, though he didn't specify how. Now, JL Wrangler Forums says the Wrangler will use the material for the hood and the doors, citing an internal bulletin from aluminum supplier Alcoa. According to the forum, the company says the next-gen Wrangler will utilize Aloca's C6A1 (an internal name) high form alloy. The SUV will also get 6022 and A951 from Alcoa that will be used on the SUV's front and rear doors, as well as for the hood. Alcoa's C6A1 is the company's new high form alloy, while its 6022 alloy sheet can be found on things like a car's hood, door, or closure panels. Alcoa's A951 is the company's pre-treatment aluminum sheet bonding technology that it uses on automobiles. "A team in the Farmington Hills (Michigan, USA) Aerospace and Automotive Products group is leading a new profitable growth opportunity with the 2018 Jeep Wrangler program. The next generation Jeep becomes the first to utilize our C6A1 high form alloy; we are currently the only supplier of this high form product. Alcoa will also supply 6022 and A951, including front and rear door inners, hood outer and inner." As Marchionne pointed out earlier this year, the 2018 Wrangler won't be made entirely out of aluminum. So Alcoa's contribution to the upcoming SUV's doors and hood could be the only components that use the lightweight metal – or Jeep could be using another aluminum supplier for other parts. Large changes lie ahead for the 2018 Wrangler, which include a pickup version, new engines, and aluminum. But we do know that the next Wrangler is that it will be built in Toledo, OH, as FCA announced plans to spend $1.05 billion to retool the Wrangler factory, while also adding another site in Illinois earlier this year. Related Video: