1950 Willys Cj-3a on 2040-cars

Auto blog

Chrysler recalls small number of 2013-2014 cars and trucks over engine debris

Chrysler is recalling a small number cars over issues with their 2.4-liter four-cylinder engines. The recall, which affects 522 examples of its 2013 Dodge Avenger and Chrysler 200 models, as well as 2014 Jeep Compass and Patriot CUVs has to do with potential debris in the balance shaft bearings.
The abrasive stuff can cause the oil pressure to drop, which could lead to the engine stalling or outright failure. This situation could at best leave drivers stranded and at worst lead to a crash.
Chrysler will begin notifying owners, who will need to report in to have the balance shaft module replaced. All repairs are naturally free of charge. Scroll down for the bulletin from NHTSA.

Certain Chrysler owners eligible for buyback program

Certain car owners whose Chrysler vehicles contain dangerous defects will soon have a way to get rid of their lemons without losing money. As part of an agreement with federal regulators, Fiat Chrysler Automobiles has agreed to buy back more than 500,000 vehicles susceptible to veering out of control without warning at above market-value prices. The deal mainly covers certain models of RAM trucks, the Dodge Dakota pickup and Dodge Durango SUV. Further, owners of more than 1.5 million Jeep Liberty and Grand Cherokees at heightened risk for lethal fires are eligible to trade in their vehicles at above market value or, alternately, get a gift certificate if they prefer to have repairs made. Chrysler has "a heavy responsibility to make sure the products they make are safe for the traveling public," said Mark Rosekind, administrator of the National Highway Traffic Safety Administration. "... Here, we are sending an unambiguous signal to industry that if you skirt the laws or violate the law, or don't live up to the responsibility that consumers expect, we are going to penalize you." The buy-back and trade-in options for motorists come as part of an unprecedented penalty NHTSA slapped against Chrysler for violating federal motor-vehicle safety laws. Chrysler will pay a $105 million fine, the highest ever levied by the regulatory agency. In addition to the buy-backs, Chrysler also agreed to an independent monitor for three years. Investigators had outlined problems in the company's conduct in 23 recalls that affected more than 11 million defect vehicles. As part of a consent-order agreement, Chrysler acknowledged it did not notify vehicle owners of recalls in an effective manner and did not notify NHTSA of safety problems. Though those recalls affected millions of drivers, the buy-back and trade-in options are only for a small portion of the vehicles involved. Because Chrysler struggled to fix the problem and no repair was apparent, Rosekind said the buy-backs are reserved "for customers who didn't have a remedy." Buy-backs are for trucks and SUVs affected by three recalls that occurred in 2013 (recalls 13V-038, 13V-527 and 13V-529), that addressed a rear-axle pinion nut that could come loose and cause a loss of vehicle control. Those recalls covered 579,228 vehicles, including 2009-2012 Ram 1500, 2500, 3500, 4500 and 5500 trucks, 2009-2012 Dodge Dakotas, 2009 Chrysler Aspen and the 2009 Dodge Durango.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.