2000 Honda S2000 Base Convertible 2-door 2.0l on 2040-cars

Auto blog

Race recap: 2016 Belgian Grand Prix is a dozen angry laps

The calm of the Formula One summer break ended with the tumult of the Belgian Grand Prix. The first two days included unusual tire pressures and grid penalties; Mercedes-AMG Petronas' Lewis Hamilton started 21st because of a 55-place grid penalty for engine and gearbox changes, McLaren's Fernando Alonso started 22nd due to a 60-place penalty for the same offenses. The bedlam rolled right into what was effectively an 11-or 12-lap race. Mercedes driver Nico Rosberg took off from pole and the cameras barely bothered with him until he took the checkered flag 44 laps later. Red Bull's Max Verstappen bogged from second on the grid, got swallowed by Ferrari's Sebastian Vettel and Kimi Raikkonen on the way to Turn 1, then attempted to recover by sticking his Red Bull's nose between Raikkonen's sidepod and the apex at the first corner. Vettel, who didn't see Verstappen, turned into La Source leaving only enough room for Raikkonen. Three cars don't fit in a space for two cars. Vettel spun, Raikkonen and Verstappen clobbered one another and all three drivers had to pit for repairs. Force India's Nico Hulkenberg zig-zagged his way into second ahead of Red Bull's Daniel Ricciardo, Williams' Valtteri Bottas, and Sergio Perez in the second Force India. On Lap 6 Kevin Magnussen lost his Renault at Raidillon at the top of Eau Rouge and flew backward into an enormous crash. Magnussen escaped with just a cut ankle. The Safety Car paraded the field for four laps before officials red flagged the race to repair the barriers. When racing resumed on Lap 10, Rosberg led Ricciardo, Hulkenberg, Alonso, and Hamilton. Ricciardo stayed ahead of Hamilton to keep second place at the end of the race, Hamilton easily got around Alonso and Hulkenberg to lock up third. Hulkenberg – who'd given up second to Ricciardo by pitting during the Safety Car period – earned another career-best fourth position ahead of teammate Perez in fifth, followed by Vettel and Alonso on recovery drives, Bottas, Raikkonen, and Felipe Massa taking 10th in the second Williams. Rosberg reignited his Driver's Championship charge with the victory, closing to nine points of leader Hamilton. We could argue that Hamilton had an equally good day by driving from 21st to third, limiting his loss to only 10 points. About that Verstappen, though... We've seen far more experienced drivers attempt the same move Verstappen made into Turn 1 – Raikkonen on Bottas in Russia in 2015, for instance.

Honda recalls Accord to replace airbag control unit

The Basics: Honda will recall 341,444 examples of the 2008-2010 Accord sedan in the US. The Problem: Moisture can enter the supplemental restraint system electronic control unit and cause corrosion. Over time, this could cause the part to fail, which might prevent the airbags from deploying in a crash. Injuries/Deaths: Honda confirms two injuries from this problem. The Fix: Dealers will replace the supplemental restraint system electronic control unit. If You Own One: Honda won't begin the recall until fall 2016 because of the large number of vehicles that will need the repair. The company will inform owners about the problem by mail in mid-March and will notify them again when the parts are available. However, if owners see the supplemental restraint system warning light illuminate before the recall begins, they can visit a dealer for a diagnostic check. If technicians find the problem, then they can replace electronic control unit immediately from Honda's limited supply of replacement parts. Related Video: Statement by American Honda Regarding SRS Electronic Control Unit Recall: 2008-2010 Honda Accord Sedan Feb 3, 2016 - TORRANCE, Calif. Approximately 341,000 Accord Sedans affected in the United States The SRS electronic control unit will be replaced, free of charge Two injuries have been confirmed related to this issue American Honda will voluntarily recall approximately 341,000 Honda Accord Sedans from the 2008-2010 model years in the U.S. to replace the Supplemental Restraint System (SRS) electronic control unit. Manufacturing process issues may allow moisture to enter the circuitry within the SRS electronic control unit, which, over time, can cause corrosion and eventual malfunction of the unit. If the SRS control unit fails from this scenario, the SRS indicator will illuminate on the vehicle's dashboard, and, in the event of a vehicle crash, the airbags may not deploy, increasing the risk of injury. Honda has confirmed two injuries related to this issue. A new SRS control unit will be installed in affected vehicles, free of charge. However, due to the large volume of new parts needed to repair affected units, the necessary parts will not be available until fall 2016. As a result, owners of affected vehicles will be informed of the recall in an initial mailed notification letter in mid-March 2016. A second notification letter will be sent to inform owners when parts become available.

Honda's 3D-printed customizable EV has motorcycle bones

Honda isn't the first company to reveal vehicles with 3D-printed panels, details and more. However, it's certainly one of the biggest, so its efforts warrant a closer look. Fresh off the heels of the Paris Auto Show, Honda showed off its Variable Design platform for micro EVs: petite cars where space -- and weight -- is at a premium. The automaker wants to offer a vehicle with a customizable layout where drivers can choose what they need. That could be lowered entry points at the doors for senior drivers, a hatchback trunk for delivery vehicles or space for a family of three. (Somehow!) Let's take a closer look: I was a bit skeptical of the idea of an entire vehicle built from 3D-printed panels, but a Honda spokesperson outlined how the company took design and engineering know-how from its motorcycle division, resulting in a light but safe pipe-based skeleton under the paneling. This is apparently what gives the "micro commuter model" structural integrity. The company had some assistance from design firm Kabuku, which put a bird on it -- on the hatchback trunk, as well as the doors and seat. The car mostly has that familiarly, rough 3D-printed surface to it, but despite being the early first step in Honda's efforts to offer a heavily customizable electric vehicle, today's prototype could very much move. A handful of journalists and businessmen got to sit inside and drive it very briefly around a corner in a faux-Japanese village. 3D-printing entire car bodies could lead to reduced design times and cheaper costs. But that's if it becomes a bigger thing. For now, it's a promising platform that's still in development.This article by Mat Smith originally ran on Engadget, the definitive guide to this connected life. Green Honda Technology Emerging Technologies Electric