2007 Honda Civic Lx Sedan 4-door 1.8l on 2040-cars

Auto blog

2015 Honda CR-V

Honda sold 335,000 CR-Vs in 2014, meaning the long-running compact CUV accounted for one in every four Honda-badged vehicles sold. And honestly, it's not too difficult to see why. It's efficient, comfortable, reasonably well equipped and reliable, much as it has always been. While it's arguably the least-exciting entry in what is, to be frank, a fairly dull class, the CR-V has always been remarkably competent at being all the vehicle its customers could possibly need. The facelifted 2015 model is all of those things and more, as we found out during a full week at the helm. Honda has been remarkably consistent in the slow evolution of the CR-V's styling over the years. If you were to compare the rear of the third-generation model (released way back in 2007 and updated in 2010) with the back of this fourth-generation version (released in 2012 and freshened for this most recent model year) you'd be hard pressed to tell one from the other. The 2007 model featured tall taillights that got wider at the bottom, while a low rear bumper, large aperture and upright tailgate made access to the rear cargo area a piece of cake... just like the 2015 model shown above. Honda has been more progressive in front for its new CR-V, however, retaining the same wide, canted headlights and three-slat grille that first appeared in 2012, but this time lining them in LED accents (as is the trend nowadays). As for the interior, the material quality is easily among the best in this fiercely competitive segment, with soft, attractive dashboard plastics. We aren't crazy about the faux leather stitching, although that's true on a lot of vehicles in this class. Other accents, like the thin strip of faux wood at the bottom of the dash, look good and have a quality feel. The leather-wrapped steering wheel is a nice item, too, and we couldn't be happier about Honda's decision to replace the old-fashioned ruched leather on the seats with cleaner, tauter hides. Those seats are quite wide and comfortable, as well, although they aren't exploding with side support for cornering (it's a Honda CR-V, after all). Visibility is excellent fore, aft and laterally, regardless of how you set up the seat. In back, leg and headroom are both in abundance, while the bench seat should prove adequate throughout a family's normal use, or on long drives. That isn't to say there aren't problems in the cabin, though.

Toyota Camry to go turbo

As automakers strive to meet regulations, turbocharging is rapidly becoming the norm whether looking at pickups, sports cars or family sedans. However, Toyota remains a stalwart to the changing tide, and for the time being a trip into one of the brand's dealers shows nary a hint of forced induction – probably not for long, though. With models like the Lexus NX 200t and forthcoming IS 200t pointing the way, a big shift is afoot for one of the Japanese automaker's most popular products. Obviously, Toyota is no stranger to forced induction for performance applications like the turbocharged models of the Supra and MR2 in the '90s. But rather than reducing lap times, the latest application is more about improving emissions and fuel economy. According to Automotive News, the Camry is getting a 2.0-liter turbo four-cylinder in the near future as a replacement for its V6 engine option. The 3.5-liter six currently in the venerable sedan already makes 268 horsepower and 248 pound-feet of torque, versus 235 hp and 258 lb-ft in the NX 200t or 241 hp and 258 lb-ft in the IS from the new four. The base four-cylinder also might receive some upgrades. It could grow larger and run on the Atkinson cycle to find improvements, according to Automotive News. There might be a move towards CVTs, as well. Toyota is hardly alone in the shift towards forced induction. Honda is known to have a 1.5-liter turbo mill on the way for the next-gen Civic. In addition, that engine might find its way into the Accord and CR-V as well, according to Automotive News. Among the major Japanese automakers, only Nissan is taking a more measured approach towards forced induction in mainstream models. Rather than going all-in on turbos, the company is expected to shift more of its engines to direct injection to go after fuel economy gains.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.