2012 Honda Cr-v Ex-l 4wd Salvage Repairable Rebuilder Only 11k Miles Runs!!!! on 2040-cars

Auto blog

Weekly Recap: Car-pedestrian crashes remained elevated in 2014

The death of American Horror Story: Freak Show star Ben Woolf served as a reminder this week that car crashes involving pedestrians remain a problem, and a new study issued on Thursday reinforced that the situation isn't really getting better. The Governors Highway Safety Association found a slight decline, 2.8 percent, in the number of pedestrian deaths in the first six months of 2014. Fatalities dropped from 2,141 to 2,125 compared with the same period in 2013, though the association says it's a statistical wash when factoring in undercounting. Deaths are still 15-percent higher than in 2009. "The number of deaths remains relatively high and is cause for concern," wrote Allan Williams, who compiled the report and is the former chief scientist at the Insurance Institute for Highway Safety. This is the first look at data from last year, and the National Highway Traffic Safety Administration will issue its full-year results later. The GHSA found some progress on the roadways, as 24 states and the District of Columbia reported drops in pedestrian deaths. In some states, the problem isn't even a problem at all: Nebraska and Wyoming reported one fatality apiece, though large population centers in urban areas are where most accidents occur. "This is a clearly a good news, bad news scenario," Jonathan Adkins, GHSA executive director, said in a statement. "While we're encouraged that pedestrian fatalities haven't increased over the past two years, progress has been slow." Other News & Notes Cadillac previews CT6 during Oscars Cadillac previewed its upcoming flagship sedan, the CT6, in commercials that aired Sunday during the Oscars. As expected, the creased sedan carries on Cadillac's recent design language, and the car in the commercial looks like a larger version of the CTS and ATS sedans. The CT6 will be revealed this spring at the New York Auto Show and launch late this year. It will be assembled at General Motors' Detroit-Hamtramck factory on a rear-wheel-drive chassis, and the CT6 is the first car to use Cadillac's revised alpha-numeric naming scheme. The commercials also kicked off Cadillac's "Dare Greatly" campaign, which is the first with its new advertising agency, Publicis Worldwide. Honda unexpectedly changes CEOs Honda unexpectedly announced this week that it will change CEOs. Current chief Takanobu Ito will step down in June and be replaced by company veteran Takahiro Hachigo.

Acura NSX production delayed

Listeners of the Autoblog Podcast will be familiar with my opinions on the Acura NSX. While I love the idea of Acura building a halo car again, I've routinely joked on-air that the car will never, ever reach production and will continue being teased and previewed ad nauseam. So I'm chuckling at this news: the NSX is being delayed again. To be fair, while it sounds like a big deal – pushing the NSX back from model year 2016 to 2017 – this is a fairly minor delay in the grand scheme. Instead of starting production this fall, as previously announced, the new supercar will start rolling down the line at Honda's Marysville, OH factory in the spring. "Trial production" has already started, Honda says, while briefly acknowledging the delay in the attached press release. While Honda offered no reason for the delay in volume production, Automobile claims it's the fault of the move to fit two turbochargers to the V6, which was made midway through development. Fitting the two iron lungs meant rearranging the six-pot into a longitudinal layout. Here's hoping there are no further delays. Scroll on for a look at Honda's press release, which does its best to gloss over the NSX delay while talking about the company's new Performance Manufacturing Center in Marysville. Related Video: Performance Manufacturing Center: Precision Craftsmanship Aug 14, 2015 - CARMEL-BY-THE-SEA, Calif. The next-generation Acura NSX is produced at the new, dedicated Performance Manufacturing Center (PMC) in Marysville, Ohio, using domestic and globally sourced parts. With trial production already underway and production start-up scheduled for spring 2016, this world-class manufacturing facility employs groundbreaking techniques in weld, body construction, body painting, final assembly and quality confirmation to ensure the highest levels of precision and craftsmanship. More details on the unique and innovative manufacturing processes at the PMC will be rolled out over the months leading up to the start of production, but the following highlights of the new facility were shared during the 2015 Monterey Automotive Week: Innovative blend of people and technology: throughout the PMC, NSX production is centered around the skills of approximately 100 experienced engineers and technicians building the NSX to precise levels of quality and craftsmanship.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.