5,000 Miles Warranty 1 Owner Clean Carfax 4cylinder Cold Ac Power Equipped on 2040-cars

Auto blog

Foreign automakers pay from $38 to $65 per hour to non-union workers

As leaders for the United Auto Workers gather in Detroit for their Special Convention on Collective Bargaining to work out the negotiating stance for this year's new labor agreements with the Detroit 3 automakers, what they most want to do is figure out how to eliminate the two-tier wage scale. However, the lower Tier 2 wage has allowed the domestic automakers to reduce their labor costs, hire more workers, and compete better with their import competition. As it stands, per-hour labor rates including benefits are $58 at General Motors, $57 at Ford, and $48 at Fiat-Chrysler – a reflection of FCA's much greater number of Tier 2 workers. The Center for Automotive Research released a study of labor rates (including benefits) that put numbers to what the imports pay: Mercedes-Benz pays the most, at an average of $65 per hour, Volkswagen pays the least, at $38 per hour, and BMW is just a hair above that at $39 per hour. Among the Detroit competitors, Honda workers earn an average of $49 per hour, at Toyota it's $48 per hour, Nissan is $42 per hour, and Hyundai-Kia pays $41 per hour. The lower import wages are aided by their greater use of temporary workers compared to the domestics. Automotive News says the ten-dollar gap between those foreign camakers and the domestics turns out to about an extra $250 per car in labor, which adds up quickly when you're pumping out many millions of cars. That $250-per-car number is one that, come negotiating time, the Detroit 3 will want to reduce, as the UAW is trying to raise both Tier 1 and Tier 2 wages. Another wrinkle is that the domestic carmakers are considering the wide adoption of a third wage level lower than Tier 2. Some workers who do minor tasks like assembling parts trays kits and battery packs already make less than Tier 2, but the UAW will be quite wary about cementing yet another wage scale at the bottom of the system while it's trying to fight a bigger battle at the top. News Source: Automotive News - sub. req., BloombergImage Credit: AP Photo/Erik Schelzig Earnings/Financials UAW/Unions BMW Chevrolet Fiat Ford GM Honda Hyundai Kia Mercedes-Benz Nissan Toyota Volkswagen labor wages collective bargaining labor costs

Honda and Acura recall 124,077 vehicles due to potential brake failure

Honda and Acura are recalling 124,077 total vehicles across numerous model lines due to a part in the brake system that was potentially improperly assembled, which could ultimately lead to brake failure. The models affected include the 2020-2021 Honda Civic, 2020-2023 Ridgeline, 2021-2023 Passport, 2021-2022 Pilot and the 2020 Acura MDX. As for the issue itself, Honda says the brake master cylinder “may have been improperly fastened to the brake booster assembly during production.” Specifically, the tie rod fastener is the problem point. Honda says that if it was improperly assembled, that could result in loose or missing tie rod nuts. If this is the case, when you hit the brakes, a bending load can be placed on the brake booster tie rod studs, which could in turn cause the tie rod studs to break. This then allows the brake master cylinder to separate from the brake booster, which Honda says could result in diminished or lost brake function. Honda says it received a report of brake failure on a 2021 Pilot last year, which prompted the companyÂ’s investigation. There are no crashes, injuries or deaths related to this issue, according to Honda, but it has received two related warranty claims since September 2022. Owner notifications are scheduled to begin on August 7 this year. Honda says it will inspect and replace any missing nuts, and if any brake booster assembly components are damaged, those will be replaced, too. Related video: Recalls Acura Honda Truck Crossover Hatchback SUV Sedan

Honda S660 set for Yokkaichi production next year

Roadsters, you might argue, are best when they're small and nimble. If you're thinking of the Mazda MX-5 Miata, you're on the right track, but there have been even smaller ones: pint-sized, three-cylinder roadsters like the Daihatsu Copen, Suzuki Cappuccino and Smart Roadster. But the most iconic and enduring of them was surely the Honda Beat.
Designed by Pininfarina, the Beat was - not unlike the F40 was for Enzo Ferrari - the last car approved for production by company founder Soichiro Honda. It complied with Japan's strict Kei car regulations and packed a tiny, naturally aspirated 656 cc that produced just 63 horsepower. The cult classic ended production in 1996, but six months ago Honda hinted at a revival with the presentation of the S660 concept at the 2013 Tokyo Motor Show. Now it seems Honda - or Yachiyo, we should say - is gearing up to put it into production at the same factory that produced the Beat two decades ago.
That plant is the Yokkaichi factory, a facility owned by Yachiyo Industry Co., Ltd. that builds small cars on contract for Honda. It was slated for a major expansion a few years ago until Honda shifted some of its small car production to its own plant in Suzuka, but continues to build the N series of boxy, upright hatchbacks, as well as small commercial vehicles like the Life and Vamos lines. The reintroduction of a small roadster line to the factory's output sometime in 2015 will undoubtedly be a cause for celebration in Yokkaichi. For our part we can only hope that American Honda CEO Tetsuo Iwamura gets his way and manages to bring the S660 to the US in the near future.