2010 Gmc Yukon Denali on 2040-cars

Auto blog

GM recalls 3.8 million vehicles in North America due to braking issue

WASHINGTON — General Motors Co said Wednesday it was recalling 3.46 million U.S. pickup trucks and SUVs to address a vacuum pump issue that could make braking more difficult and that has been linked to 113 accidents and 13 injuries. The recall covers 2014-2018 model year vehicles, including some Cadillac Escalade, Chevrolet Silverado, Chevrolet Tahoe, GMC Sierra, Chevrolet Suburban and GMC Yukon vehicles. In late June, GM recalled 310,000 vehicles in Canada for the same issue. GM did not immediately explain why the Canadian recall occurred more than two months before it called back the vehicles in the United States. The recall was triggered because the amount of vacuum created by the vacuum pump may decrease over time, GM told the National Highway Traffic Safety Administration (NHTSA) in documents posted on Wednesday. The NHTSA opened a preliminary investigation into the issue last November, and said it had reports of nine related crashes and two injuries. It provided GM in July with additional field reports that prompted the automaker to open an investigation. GM said it could affect braking in "rare circumstances." The NHTSA said in a statement the "vehicles may experience brake boost failure, which would require increased brake pedal effort, leading to a hard brake pedal feel, and potentially increased stopping distance." GM said dealers will reprogram the electronic brake control module to improve how the system utilizes the hydraulic brake boost assist function when vacuum assist is depleted. GM said the vacuum assist pump, which is lubricated with engine oil that flows into the pump through a filter screen, can in some cases lose effectiveness over time, as debris such as oil sludge can accumulate on the filter screen. GM told NHTSA that prior model years used a different brake assist system design, and vehicles manufactured after 2018 were not equipped with the affected pump design. Separately, GM said on Wednesday it is recalling 270,000 additional U.S. vehicles in three smaller recalls, including 177,000 2018 Chevrolet Malibu cars with 1.5L turbo engines because an error in the engine control module software may result in the fuel injectors being disabled.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

Texas sues GM, saying it tricked customers into sharing driving data sold to insurers

Texas filed a lawsuit Tuesday against GM over years of alleged abuse of customers' data and trust. New car owners were presented with a "confusing and highly misleading" process that was implied to be for their safety, but "was no more than a deceptively designed sales flow" that surrendered their data for GM to sell. The suit contends that at no point was selling driving data ever even suggested as a possibility, putting GM in violation of the state's consumer protection laws. Texas Attorney General Ken Paxton is seeking a jury trial and at least $10,000 per offense (every GM car sold in the state since 2015) and a hefty add-on of $250,000 in cases where the victim was over 65. Texas seems to be flying high after a recent $1.4 billion settlement from Meta over other privacy concerns. This may well be a way to solve any pending budgetary issues in the Lone Star State.