2008 Gmc Yukon Xl Denali Awd 7-pass Htd Leather 64k Mi Texas Direct Auto on 2040-cars

Auto blog

GM re-recalls 11k SUVs

General Motors is recalling a bunch of previously recalled SUVs because, well, they still aren't quite fixed. The latest repairs are necessary on 10,974 SUVs in North America, including 9,932 in only the US. Affected models include the 2006-2007 Buick Rainier, Chevrolet Trailblazer, and GMC Envoy; plus the 2006 Trailblazer EXT and Envoy XL. While not listed by NHTSA, a statement by GM to Autoblog says the 2006-2007 Saab 9-7X and Isuzu Ascender are also affected. In these SUVs, it's possible that liquid could get into the driver's door master power window switch module and cause a short circuit. This could potentially lead to a fire, and owners are urged to park the vehicles outside until repaired. GM has been trying to fix this issue for years. It started as an investigation into fires, and that led to a recall for about 250,000 vehicles in cold-weather states. A nationwide campaign came in 2013 for 193,000 of them in the US. Last year, the automaker decided to replace the whole module as a repair. However in a recent investigation of these recalls, GM discovered that this latest group of SUVs never received the new part. According to documents submitted to NHTSA (as a PDF), "Some dealers incorrectly used the labor code associated with module replacement when, instead of replacing the module, they only added a protective coating to the module." To fix things this time, the models finally get the correct component. Related Video: GM Statement General Motors is recalling 9,932 older midsize SUVs in the U.S. because they were mistakenly excluded from an earlier recall. Certain 2006 Chevrolet TrailBlazer EXT and GMC Envoy XL, and 2006-2007 TrailBlazer, Envoy, Buick Rainier, Saab 9-7X and Isuzu Ascender vehicles may continue to have a condition in which the printed circuit board inside the driver's door may corrode and short if exposed to certain fluids such as melted snow containing road salt. GM is aware of four fires but no crashes, injuries or fatalities associated with the expanded recall. The total number of vehicles being recalled, including Canada, Mexico and exports is 10.974. Customers are urged to park these vehicles outside until repairs have been made. GM reported this recall to the NHTSA on September 23.

GM is the latest automaker accused of diesel emissions cheating

Volkswagen and Ram need to make room on the diesel-emissions bench for General Motors. America's largest automaker was accused in a lawsuit on Thursday of rigging hundreds of thousands of diesel trucks with at least three so-called defeat devices to ensure that the trucks would meet federal and state emission standards, even if they generated more pollution in real-world driving. According to the complaint, on-road emissions testing conducted for the plaintiffs found that Duramax-equipped trucks produced NOx pollutants, comprised of nitrogen and oxygen atoms, two to five times higher than legally permitted, and "many times" higher than their gasoline counterparts. The proposed class-action lawsuit was filed in federal court in Detroit on behalf of people who own or lease more than 705,000 Chevrolet Silverado and GMC Sierra pickup trucks fitted with "Duramax" engines from 2011 to 2016 model years. The lawsuit seeks remedies including possible refunds or restitution for lost vehicle value, plus punitive damages. It adds to legal problems for Detroit-based GM, which has already paid about $2.5 billion in penalties and settlements over faulty ignition switches linked to 124 deaths. GM joins at least five automakers whose diesel emissions have been scrutinized by regulators or consumers. They include VW, which has admitted to cheating; Mercedes-Benz parent Daimler; Fiat Chrysler Automobiles, Peugeot and Renault. GM spokesman Dan Flores called the claims "baseless," and said the trucks comply with US Environmental Protection Agency emissions standards and California's own tough standards. Shares of GM were down 69 cents, or 2.1 percent, at $32.50 in afternoon trading, after earlier falling to $31.93. The GM lawsuit was filed by several law firms, including Hagens Berman Sobol Shapiro, which helped reach multibillion-dollar settlements with VW on behalf of drivers and dealers. The case is Fenner et al v General Motors LLC et al, US District Court, Eastern District of Michigan, No. 17-11661. The named plaintiffs are Andrei Fenner of Mountain View, California and Joshua Herman of Sulphur, Louisiana. They said they would not have bought their respective 2011 Sierra and 2016 Silverado trucks, or would have paid less for them, had they known about the alleged rigging. Joseph Spak, an RBC Capital Markets analyst, in a research report said "negative publicity" from the lawsuit could drive buyers to trucks from Ford or even Fiat Chrysler's Ram.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.