Repaireable Rebuildable Salvage Lot Drives Great Very Easy Project Builder Fixer on 2040-cars

Auto blog

2019 GMC Sierra 1500 prototype shows off differences from Silverado

Now that the new Silverado has made its debut, we're awaiting the reveal of its mildly restyled twin, the GMC Sierra 1500. While it likely won't be that different as far as capability and major equipment are concerned, we are looking forward to seeing what design changes it will have. Based on these recent spy shots, the changes will be mild, but still enough to make it visually distinctive. One of the more obvious differences will be in the front fascia treatment. Unlike the Silverado's grille that's level with the top of the headlights, the GMC's will rise above the lights, which will also yield a slight drop on each side of the hood to meet the lights. The grille is quite tall, extending far below the headlights, too. We can make out, behind some mesh, two dips on the outer edges of the grille that give the Sierra a more menacing frown. Large foglights are also found right near where the scoops for the wheel air curtains, and the headlights are unified on the edges, rather than split on the Silverado. Along the sides, the sheet metal looks relatively unchanged. At some angles, we can make out the distinctive shoulder line from the Silverado that runs up to about the rear mirrors where it stops to make room for another crease that rises up from somewhere in the middle of the front doors to lead to the front. The wheel arches are decidedly different from the Silverado's though. While the Silverado has fairly rounded arches, the Sierra's have a rear-slanted bevel to the fronts of the arches and a rounded 90-degree corner at the rears. There isn't much we can tell about the rear except for the taillights. They're quite large, and unlike the Silverado's, there aren't any areas where the sheet metal intrudes. It also appears that the tops of the taillights extend farther forward into the bed sides than the Chevy's. Because the Sierra has almost always been a mechanical twin of the Silverado, we expect it to offer the same 5.3-liter and 6.2-liter V8s, as well as the new 3.0-liter diesel inline-6. Also, being a GMC, it will likely have a flashy, chrome-laden Denali trim level. We also will see the fully revealed model soon, as Automotive News reports the debut will be on March 1. Related Video: Featured Gallery 2019 GMC Sierra 1500 spy shots View 39 Photos News Source: Automotive News Spy Photos GMC Truck chevrolet silverado

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles

GMC Hummer EV fan's Lego build is functional and even has Crab Mode

Lego creates some pretty amazing automotive models, but the Lego hobbyist community sometimes does better. Evidence of that comes to us in this fully-functional GMC Hummer EV Lego Technic model spotted by Road & Track and created by YouTube user Alain B. And while it's a one-off for now, there is the possibility it could become a kit you could bring home. As you can see in the video, the model looks the part with a body that closely matches the real thing. It's an impressively solid body, too, something that's sometimes difficult to achieve with Technic pieces. But that's only the tip of the iceberg. It's also got electric motors and is remote controlled. It has four-wheel-steering that can emulate the Hummer's famous Crab Mode setup. The fully independent suspension can raise for more ground clearance. And on top of all of that, it's even got a fully operational MultiPro tailgate and front trunk. The design is also listed on the Lego Ideas page. This is the site where Lego builders can submit their creations, and if they get enough votes, they'll be considered by the company for becoming a real production kit. You can visit the page at this link to lend your support (it doesn't cost anything). That page also reveals some other neat details, including the fact that it's made of about 2,200 pieces. While enough votes will get the design to be considered by Lego, there are other factors that determine whether it makes production. Some of them include getting the license from General Motors, and other undisclosed reasoning. But Lego has done a number of large, technical and somewhat pricey kits with licensing from other companies. So this seems like a great one for the company. Related video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.