2005 Gmc Sierra 2500hd 4x4 Slt Extended Cab 6.0 Vortect on 2040-cars

Auto blog

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2017 GMC Canyon Denali brings the bling

Denali is an incredibly important part of GMC's product strategy. It takes very little effort to create a Denali variant, and these models retail for big premiums over the models on which they're based. So if you're GMC, it makes sense that you'd want to create a Denali version of every product in your range. That in mind, enter the 2017 Canyon Denali. GMC's midsize pickup gets all of the usual Denali trimmings, including a new grille, chrome trim, 20-inch wheels, and the necessary badging. Inside, there's a unique instrument panel, Jet Black leather, heated and cooled seats, and again, Denali badges abound. GMC says the Canyon Denali will be offered exclusively in the crew cab body style, with either the 3.6-liter gasoline V6 or 2.8-liter diesel engine. Have a look at the fancy truck in our gallery above, and scroll down for GM's official press blast. GMC Introduces 2017 Canyon Denali Exclusive design cues, content elevate industry's first premium midsize truck DETROIT, Tuesday, Nov. 17, 2015 – Denali is the ultimate expression of GMC's professional grade style, luxury and capability – and it is coming to the Canyon midsize truck. The 2017 Canyon Denali is being introduced today, ahead of its public debut at the Los Angeles Auto Show. It goes on sale in late 2016. "Canyon is the segment's first and only premium midsize truck, offering unparalleled capability and efficiency matched with maneuverability and refinement," said Duncan Aldred, vice president of GMC Sales and Marketing. "The all-new Canyon Denali builds on that award-winning combination with the distinctive styling, luxurious interior and elevated content that has defined the Denali nameplate since its introduction nearly 17 years ago." Like all Denali models, the new Canyon Denali is distinguished with a unique chrome grille and unique wheels – 20-inch ultra-bright-machined aluminum wheels with painted accents. Exterior cues include chrome fog lamp bezels, five-inch-diameter rectangular chrome assist steps, a polished exhaust tip and a standard spray-in bed liner. The Canyon Denali will be offered in six exterior colors. Inside, a Jet Black interior features Mulan leather-appointed seats with perforated, heated-and-ventilated front seats – exclusive content in the Canyon lineup – along with unique instrument panel and console trim; and Denali-logo sill plates and floor mats. Standard technologies include Forward Collision Alert and Lane Departure Warning.