No Reserve Ext Cab 6000 Vortec Alloy Heated Leather Awd *quadrasteer Broken* on 2040-cars

Auto blog

GM recalls nearly 340,000 large SUVs to fix daytime running lights

General Motors has initiated a recall campaign for more than 338,000 of its large SUVs to address a potential defect in the onboard computer software that controls the daytime running lights. In some cases, the DRLs may remain on even when the headlights are enabled, which creates additional glare for oncoming drivers at night and fails to comply with federal regulations for headlight performance.  "GM determined that the body control module (BCM) software in these vehicles, under a combination of certain pre-conditions, may fail to deactivate the DRLs when the headlamps are on," GM's recall report said. "A regulatory assessment was conducted to evaluate whether the condition presented a potential noncompliance with the DRL activation requirements in S7.10.5, Table I-a. of FMVSS 108. On October 27, 2022, GM’s Safety Field Action Decision Authority (SFADA) decided to conduct a recall for potential noncompliance with this standard." GM says the recall covers the 2021 model year GMC Yukon and Yukon XL, 2021 Chevrolet Tahoe and Suburban, and 2021 Cadillac Escalade and Escalade ESV. The company says all models produced within that operating window include the improperly programmed body control module, meaning all vehicles within the recall population may exhibit the problem. The issue was discovered by a GM engineer during validation testing in August, prompting a deeper investigation and eventually leading to the recall itself.   The module's software can be updated by GM dealers, so it should be a quick fix for customers. Notifications will be mailed to owners in December.  Related video: Recalls Cadillac Chevrolet GMC Ownership Safety SUV Luxury

GM expanding Lansing Lambda CUV plant

Considering that crossovers are a rapidly growing portion of the US auto market, it's not surprising to hear that General Motors is preparing to build even more of them. The company is investing $63 million to expand its Lansing Delta Township Assembly plant that builds Lambda platform CUVs like the Chevrolet Traverse, GMC Acadia and Buick Enclave.
According to GM, the expansion will add roughly 263,000 extra square feet of space to the plant. Of that, 181,000 square feet will be for an updated body shop with cutting-edge robots. There will also be 54,000 square feet of additional room in the paint shop and 28,000 square feet of more area for general assembly.
GM isn't saying as much, but there is the possibility that this extra space could allow for additional models produced at the factory. Cadillac reportedly dropped plans to build a three-row SUV on the Lambda platform earlier this year, however, dealers for the luxury brand were recently pitched the possibility of adding large and small CUVs, an ATS convertible or a sedan below the ATS.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck