Savana New Van Automatic 4.8l 8 Cyl Summit White on 2040-cars

Auto blog

2017 GMC Acadia loses 700 pounds, gains everywhere else

Ladies and gentlemen, welcome to Acadia. The 2017 version of the three-row GMC crossover has all kinds of newness. The 2017 Acadia has lost 700 pounds compared to its predecessor thanks to high-strength steels allowing redesigned parts, and the fact that it overall, the vehicle is actually smaller. Length is reduced by 7.2 inches on a wheelbase diminished by 6.4 inches, it is 3.5 inches narrower and sits 3.9 inches lower. The 2016 Acadia was 4,656 pounds, the 2017 is 3,956 pounds. GMC says it will still swallow people, but not as many: the eight-passenger option didn't make the transition, potential three-row trims permitting five-, six-, and seven-passenger configurations. While you lose space, you gain convenience with a split-folding second row featuring tilt-and-slide for both sections. The third-row seats fold flat into the cargo floor, and if the second row is folded as well, cargo capacity improves over the 2016 Acadia, 79 cubic feet compared to 70 cu-ft. A new 2.5-liter four-cylinder brings a second engine option to the spec sheet, returning an estimated 22 city miles per gallon and 28 highway mpg with the help of stop/start tech on front-wheel-drive trims. The new 3.6-liter V6 gets around 310 horsepower, a power bump of about 19 hp, and an estimated 25 highway mpg in front-wheel-drive guise. Towing capacity for that V6 goes down, though, from 5,200 on the current Acadia to an estimated 4,000 pounds. The optional Tow Vision Trailering system will make that pulling easier. Both engines are hooked to a six-speed automatic. Now we can get to its looks. Trademarks like the square, flared wheel arches, dark D-pillars, and wraparound rear side windows made the transition, everything else is new. While weight has gone down, safety's gone way up with internal changes like the splayed chassis members to confront the small-offset test. New active safety upgrades run from from three kinds of automatic braking systems to surround vision cameras, automatic high beam control, a safety alert seat, and a following distance indicator. Buyers can choose from a front-wheel drive, all-wheel drive, or All Terrain model, each with its own electronic drive selector modes. The Normal, Sport, and Trailer/Tow modes are common to the trio. The FWD gets a Snow mode, the AWD adds adaptive 4x4 and Off Road modes; on the AWD, the 2x4 mode disconnects the rear axle from the drivetrain.

2021 Chevy Colorado and GMC Canyon facelift spied

The Chevy Colorado and its GMC Canyon twin have been on sale for a good long time now, and while things move a little more slowly on the truck side when it comes to facelifts and model changeovers, it seems like it’s about time. So itÂ’s no surprise to see some lightly camouflaged trucks running around ahead of what appears to be a minor refresh for the 2021 model year. Starting with the Colorado, it appears to have a bowtie hiding behind some camo in the center of the grille, which otherwise looks like the no-bowtie option you can get on 2019-and-up trucks. It could be that Chevy is keeping the no-bowtie grille design but allowing a bowtie to grace it, or it could be misdirection. Either way, the grille pattern adds a bit of flair to the otherwise staid front end design. There also appears to be a bit more shape to the lower air inlet, with echoes of some of the lower fascias of its bigger Silverado stablemate. The Canyon, on the other hand, shows more extensive front-end changes. At first glance, it looks to emulate some variants of the GMC Sierra, which would make sense given those modelsÂ’ changes for the 2020 model year. In particular, this Canyon has hints of Sierra HD, being more square and monolithic than the regular Sierra 1500s, although itÂ’s a little hard to tell with the camo covering the edges of the grille. It could certainly also adopt more rounded corners like the 1500s. Either way, itÂ’s more vertical and thereÂ’s less differentiation between the upper grille and lower opening. ThereÂ’s nothing in the way of changes around the sides or back, and while there may be some minor changes inside, we arenÂ’t expecting any. The word around town is that this isnÂ’t a full facelift, but rather a minor front end tweak thatÂ’ll just be a regular part of the model-year changeover. 

How Chevy Silverado, GMC Sierra will take on the Ford F-150 profit machine

FORT WAYNE, Ind. — When General Motors engineers were developing the 2019 Chevrolet Silverado and GMC Sierra pickup trucks, some of them joined public tours of Ford's Dearborn, Mich., factory to watch aluminum-bodied F-Series trucks go down the assembly line. The redesign of the Ford F-Series trucks, launched in 2014, set a new standard for fuel economy and lightweight vehicle construction. But armed with stopwatches and trained eyes, the GM engineers believed they saw problems. "They had a real hard time getting those doors to fit," Tim Herrick, the executive chief engineer for GM truck programs, told Reuters. His team did more intelligence gathering. They bought and tore apart Ford F-Series doors sold as repair parts. Their conclusion: GM could cut weight in its trucks for a lower cost using doors made of a combination of aluminum and high-strength steel that could be thinner than standard steel, shaving off kilograms in the process. These pounds-and-pennies decisions will have major implications in the highest-stakes game going in Detroit: dominance in the world's most profitable vehicle market, the gasoline-fueled large pickup segment. What's more, GM is banking on strong sales of overhauled 2019 Silverados and GMC Sierras to fund its push into automated and electric vehicles — a business many investors see as the auto industry's long-term future. The risks are high given the hits automakers have taken from U.S. President Donald Trump's trade policies. Rising aluminum prices spurred by Trump's tariffs are driving up costs on the Ford's F-Series, while rising steel and aluminum prices likewise drag on GM results. GM also has a significant risk should the United States, Mexico and Canada fail to agree on a new NAFTA trade deal, given GM trucks built at its Silao, Mexico, factory could face a 25 percent tariff if NAFTA collapses. Major profit per truck Interviews with GM executives and a tour at its factory here in northwest Indiana provide a detailed look inside GM's plan for the most important vehicles in its global lineup. These big pickups are everything Tesla's Model 3 or Chevy's Bolt electric car is not. The mostly steel body is bolted to the truck's steel frame, rather than the one-piece body and frame electric vehicles. The majority of trucks will have a V-8 gasoline engine powering the rear wheels — like the classic GM cars of the 1950s. Some Silverados will have new four-cylinder engines, but there is no electric or hybrid offering as of now.