2002 Gmc Savana 1500 Explorer Limited Conversion Van , Mint Mint on 2040-cars

Auto blog

Next-generation Chevrolet Colorado breaks cover in new spy photos

The next-generation Chevrolet Colorado broke cover in this fresh set of spy photos this week, giving us a glimpse of what to expect when GM's compact trucks are replaced in what is expected to be either 2023 or 2024.  Thanks to its still-extensive camouflage, this prototype doesn't give away a ton about the new Colorado's styling, but in profile, it appears as though the swoopy, upswept rear cab line might become a thing of the past. We wouldn't be surprised to see the new Colorado adopt a more angular, squared-off look more akin to that of its big brother, the half-ton Silverado. The Silverado is also expected to donate what may be the new Colorado's only powertrain. Taking a cue from Ford, Chevy is expected to offer the next-gen Colorado with just a turbocharged four-cylinder engine — the new corporate 2.7T in this instance. The large, 310-horsepower four-pot can easily take over for the 3.6L V6 currently available in the GM twins and one-up the 270-hp Ranger to boot. This would mark the end of both a V6 and diesel option being offered in GM's midsize trucks, and tracks with the company's slow, silent effort to eliminate lower-margin models. We say "trucks" because, well, whatever happens with Chevy is likely to translate to GMC. The Canyon will be due for replacement at the same time, and will likely carry on as a re-skin of Chevy's offering. We're not yet certain exactly when Chevrolet will start selling the next-gen Colorado, but given the reasonably complete state of this prototype, we expect it won't be long now. Rumors suggest it could hit the market in 2023 as a 2024 model.  Related Video: The Best Midsize Pickup: Ranger vs Gladiator vs Tacoma vs Colorado

2015 GMC Yukon erupts into flames during Anaheim test drive [w/video]

A 2015 GMC Yukon burst into flames while on a test drive in Anaheim, CA on Sunday after smoke filled the cabin. Residents of the neighborhood where the driver abandoned the redesigned Yukon reported hearing a series of small explosions (likely the tires, based on the video), according to a report from KTLA and The Los Angeles Times.
No one was injured in the incident, which The Times reports occurred after a possible oil or fluid leak. As you can see in the image above, the Yukon was engulfed in flames, although the Anaheim Fire Department was able to put out the blaze in about 15 minutes.
"We're very lucky that no one got hurt, and it was in an area that... was safe," Lt. Tim Schmidt of the Anaheim Police Department told KTLA reporters. "If there was any place that was going to be safe, it would be this area. It's very open. It worked out for us."

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.