2017 Gmc Acadia Limited on 2040-cars

Auto blog

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

Chevy Colorado and GMC Canyon get trim levels reworked again

GM Authority reports that GM has fiddled with trim packages on the Chevrolet Colorado and GMC Canyon for the 2021 model year, eliminating the base trims on both pickups and implementing small price changes. When the new model year goes on sale, the Chevy will lose the rear-wheel drive Base Extended Cab with the automatic transmission that starts at $22,395 after a $1,095 destination charge. The new entry-level is going to be the Work Truck model with the extended cab in rear-wheel drive, starting at $26,595 assuming the destination charge holds steady. That represents a $4,200 jump over the base 2020 model. MSRPs for the entire Work Truck lineup, from base to the Crew Cab Long Box, rise by $400. Elsewhere in the Colorado line, the four Z71 trims go down by $100, while the two ZR2 trims increase by the same amount. Only the six LT trims don't see any change.  The GMC side is a bit more involved due to previously announced changes. The 2020 Canyon comes in SL, Base Canyon, SLE, SLT, All Terrain, and Denali steps. Last month, GM Authority reported the 2021 Canyon would give all that up for the new names Elevation Standard, Elevation, AT4, and Denali. Since the SL base model retires in 2021, the Elevation Standard takes over at the entry level. Unlike on the Colorado, which sheds one trim, the Canyon lineup gets pared from 20 total combinations of trims, cab sizes, and bed lengths, to 14 total combinations. But like the Colorado, due to the loss of the cheapest configuration, the least expensive 2021 Canyon becomes $4,200 more expensive than in 2020, assuming the destination price remains the same. What's more, the 2021 Elevation Standard pricing adds $700 or $800 to the prices of the 2020 Canyon base and SLE models. There are more increases up the range. The 2021 Elevation trim replaces a combination of SLE and SLT models, bumping prices up by up to $900. In 2020, the least expensive All Terrain model is the Extended Cab Cloth for $37,695. For next year, the least expensive AT4 trim is the Crew Cab Short Box for $39,295. Like-for-like, though, the AT4 represents a $300 premium over the 2020 All Terrain Crew Cab Short Box. Three Denali trims will still stand at the top of the heap, each one going up by $400 in 2021. Until GM details the equipment changes, we won't know how the new pricing equates to value.

2024 GMC Sierra HD prices start at $46,295, increasing $100 to $2,500

After an online reveal in October of last year, prices for the 2024 GMC Sierra HD have crept online thanks to GM Authority. The upscale heavy duty pickup gains a new-look design and a more powerful turbodiesel V8 that boosts the tow ratings every HD buyer likes to keep up their sleeves like aces. The optional 6.6-liter turbodiesel Duramax V8 increases horsepower 25 ponies to 470 and torque by 65 twists to 975 pound-feet, both numbers matching the 2024 Chevrolet Silverado HD's diesel output. The torque comes with more useful delivery as well, GMC saying it increased low-end twist by about 25% thanks to a new turbocharger. Buyers who go for the 6.6-liter gas V8 will command 401 hp and 464 lb-ft. Both engines run output through a ten-speed automatic. One the gasser, the new gearbox replaces a six-speed auto. The standard 2500 HD's towing capacity checks in at 22,500 pounds (a 4,000-pound improvement), the 3500 HD capable of towing up 36,000 pounds. Broadly speaking, designers drew a more angular front end with a new-look grille, sharper-looking lights, and a redesigned bumper. New wheels are part of the update as well; the 3500 HD dually gets 18-inch polished aluminum wheels, and 22-inch units are optional on single-rear-wheel trucks. Finally, the color palette grows with six optional shades called Titanium Rush Metallic, Sterling Metallic, Volcanic Red Tintcoat, Redwood Metallic, Meteorite Metallic and Downpour Metallic. Configuration variables include Regular, Extended and Crew cabs, and Pro, SLE, SLT, AT4, AT4X, Denali and Denali Ultimate trims. The AT4X is late availability, the Denali Ultimate is new for 2024. The Denali Ultimate comes with the 6.6-liter turbodiesel V8, a trim-specific grille, 20-inch machined-aluminum wheels with high-gloss black accents, power-operated running boards, leather upholstery, wood interior trim, massaging front seats, a Kicker sound system and exterior emblems featuring Alaska's 20,310-foot Mount Denali.  Pricing is up by $100 to to $2,500 depending on trim.