Auto blog

2024 GMC Sierra HD unveiled with new design and more powerful turbodiesel V8

The 2024 Chevrolet Silverado HD made its debut in September 2022, so it was only a matter of time before the GMC Sierra HD received a similar round of updates. Unveiled online, the truck gains a new-look design and a more powerful turbodiesel V8, among other changes. GMC developed the Sierra HD primarily for towing and hauling so the most significant changes are found under the hood. The available 6.6-liter turbodiesel Duramax V8 engine now develops 470 horsepower at 2,800 rpm and 975 pound-feet of torque at 1,600 rpm, figures that represent increases of 25 and 65, respectively, over the 2023 model and that match the 2024 Silverado HD's. GMC notes it increased low-end torque by about 25% by fitting a new turbocharger. The V8 spins the rear or the four wheels via a 10-speed automatic transmission.  On the gasoline side of the spectrum, the 6.6-liter V8's output stays flat at 401 horsepower and 464 pound-feet of torque. It's now bolted to a 10-speed automatic transmission, and replacing the 2023 truck's six-speed lets the engine run closer to its peak power for longer periods. Here again, rear-wheel-drive comes standard and a part-time four-wheel-drive system is available across the entire line-up. Properly equipped, the 2024 Sierra 2500 HD Crew Cab can tow up to 21,900 pounds. The standard 2500 HD's towing capacity checks in at 22,500 pounds (a 4,000-pound improvement), and the 3500 HD is capable of towing up to 36,000 pounds — that's nearly 13 Subaru BRZs. Buyers have a dizzying selection of trim levels and body styles to choose from. The range includes Regular, Extended, and Crew cabs as well as seven trim levels called Pro, SLE, SLT, AT4, AT4X, Denali, and Denali Ultimate, respectively. The AT4X variant will not be available at launch, and the Denali Ultimate is new for the 2024 model year. Additionally, 3500 HD models can be ordered with dual rear wheels. What the truck looks like depends on the trim level. Broadly speaking, designers drew a more angular front end with a new-look grille, sharper-looking lights, and a redesigned bumper. New wheels are part of the update as well; the 3500 HD dually gets 18-inch polished aluminum wheels, and 22-inch units are optional on single-rear-wheel trucks. Finally, the color palette grows with six optional shades called Titanium Rush Metallic, Sterling Metallic, Volcanic Red Tintcoat, Redwood Metallic, Meteorite Metallic, and Downpour Metallic, respectively.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GM’s move to Woodward is the right one — for the company and for Detroit

Back in 2018, Chevy invited me to attend the Detroit Auto Show on the company dime to get an early preview of the then-newly redesigned Silverado. The trip involved a stay at the Renaissance Center — just a quick People Mover ride from the show. IÂ’d been visiting Detroit in January for nearly a decade, and not once had I set foot inside General MotorsÂ’ glass-sided headquarters. I was intrigued, to say the least. Thinking back on my time in the buildings that GM will leave behind when it departs for the new Hudson's site on Woodward Avenue, two things struck me. For one, its hotel rooms are cold in January. Sure, itÂ’s glass towers designed in the 1960s and '70s; I calibrated my expectations accordingly. But when I could only barely see out of the place for all the ice forming on the inside of the glass, it drove home just how flawed this iconic structure is.  My second and more pertinent observation was that the RenCen doesnÂ’t really feel like itÂ’s in a city at all, much less one as populous as Detroit. The complex is effectively severed from its surroundings by swirling ribbons of both river and asphalt. To the west sits the Windsor tunnel entrance; to the east, parking lots for nearly as far as the eye can see. To its north is the massive Jefferson Avenue and to its south, the Detroit River. You get the sense that if Henry Ford II and his team of investors had gotten their way, the whole thing would have been built offshore with the swirling channel doubling as a moat. This isnÂ’t a building the draws the city in; itÂ’s one designed to keep it out. Frost on the inside of the RenCen hotel glass. Contrasted with the new Hudson's project GM intends to move into, a mixed-use anchor with residential, office, retail and entertainment offerings smack-dab in Detroit's most vibrant district, the RenCen is a symbol of an era when each office in DetroitÂ’s downtown was an island in a rising sea of dilapidation. Back then, those who fortified against the rapid erosion of DetroitÂ’s urban bedrock stood the best chance of surviving. This was the era that brought us ugly skyways and eventually the People Mover — anything to help suburban commuters keep their metaphorical feet dry. The RenCen offered — and still offers — virtually any necessity and plenty of nice-to-haves, all accessible without ever venturing outside, especially in the winter, but those enticements are geared to those who trek in from suburbia to toil in its hallways.