2011 Gmc Acadia Denali Awd Only 16k Miles Superb Condition Clean Carfax on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalling 15k midsize pickups over leaky brakes

General Motors has announced a recall in coordination with the National Highway Traffic Safety Administration related to the brakes on the 2015 Chevy Colorado and GMC Canyon. In the 14,838 units in the United States estimated to be affected, the front brake calipers may be leaking fluid. Needless to say, that could make them less effective, which could hinder the vehicle's ability to stop in time to avoid a collision. The affected units were all manufactured between January 6 and December 24, 2014. The fix seems simple and straightforward enough, with dealers being instructed to inspect the front brake calipers, and replace them if necessary. See below for all the details from NHTSA. RECALL Subject : Brake Fluid Leak Report Receipt Date: MAY 12, 2015 NHTSA Campaign Number: 15V278000 Component(s): SERVICE BRAKES, HYDRAULIC Potential Number of Units Affected: 14,838 Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2015 Chevrolet Colorado, and GMC Canyon trucks manufactured January 6, 2014, to December 24, 2014. The affected vehicles may experience the front brake calipers leaking brake fluid. This is due to air pockets, an imperfection in the metal caliper body. CONSEQUENCE: If the vehicle experiences a brake fluid leak it can increase the stopping distance, increasing the risk of a vehicle crash. REMEDY: GM will notify owners, and dealers will inspect and replace the front-brake calipers if necessary, free of charge. The recall is expected to begin July 10, 2015. Owners may contact GM customer service at 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14888. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov. Related Video: Featured Gallery 2015 Chevrolet Colorado: First Drive View 38 Photos News Source: National Highway Traffic Safety AdministrationImage Credit: Copyright 2015 Seyth Miersma / AOL Recalls Chevrolet GMC Truck gmc canyon brakes

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.