1950 Gmc 100 on 2040-cars

Auto blog

GM alerting truck and sedan owners to a do-over on brake recall

A recall campaign intended to address issues with braking systems on certain 2019 General Motors trucks and sedans may have introduced a new issue, the automaker has acknowledged, and thousands of owners driving repaired vehicles may need to return to their service departments for another update.  The update addresses a fix that was pushed out to owners of more than half a million brand-new GM trucks and sedans that could potentially lose partial braking function, according to the Detroit Free Press. The original software fix helped address situations where the vehicles' anti-lock braking systems would become disabled, which in turn would prevent electronic stability control from activating. Vehicles subject to the recall would often experience software glitches that prevented them from properly communicating the operational state of these systems, meaning drivers would have no idea that their brakes may not behave as expected in an emergency. The 2019 Chevrolet Silverado 1500, Cadillac CT6, and GMC Sierra 1500 were all recalled in the original campaign.  Unfortunately, the early version of this fix appears to have introduced yet another software glitch, indicating that the original fix did not do the trick. Those who have not yet had their cars serviced can rest easy; they will only receive the most up-to-date version of the software fix.  Related video    

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.

Chevrolet Silverado, GMC Sierra could get independent rear suspension

The Chevrolet Silverado and the GMC Sierra could reportedly receive a variant of the four-link independent rear suspension found under the new Tahoe and Suburban. While that's not a surprise, a recent report suggests electrification, not comfort, convinced General Motors to make the change. Replacing the time-tested solid rear axle with an independent suspension will improve comfort, handling and off-road prowess, while adding weight, and likely making the trucks a little bit more expensive. It's a fair trade-off, but GM Authority learned the real reason for the swap is that at least one of the pickups will spawn an electric model, and it's more difficult to package a bulky battery pack around a solid rear axle. The independent rear suspension takes up far less space, even if it has more moving parts. General Motors will build its first regular-production electric pickup on an evolution of the Silverado's T1 platform named BT1, according to the same source. The b stands for -- you guessed it -- batteries. The firm reportedly doesn't want to make two suspensions for cost reasons, so the independent setup will come standard regardless of whether the truck runs on gasoline, diesel, or electricity. As a bonus, Chevrolet and GMC could choose to offer their T1-based trucks with Magnetic Ride Control or an air suspension, options available on the 2021 Suburban and Tahoe. The independent rear suspension will also find its way to the next-generation GMC Yukon due to be revealed January 14, and to the 2021 Cadillac Escalade scheduled to make its debut February 4. The long-rumored, born-again Hummer will get it, too, because it will arrive as an electric model built on the BT1 platform. It's worth noting none of this is official, and General Motors has remained quiet about what's next for its new suspension design, and what will be under its electric truck's sheet metal. If the GM Authority report is accurate, the Silverado (pictured) and the Sierra could ditch their solid rear axle for the 2021 model year. The change will likely be accompanied by other tweaks inside and out. Featured Gallery 2019 Chevrolet Silverado 1500 View 16 Photos Chevrolet GMC Truck