1966 Ford Thunderbird T-bird Coupe Automatic 390 V8 Fresh Trans Rebuild on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Shelby to auction 2012 GT350 No. 1 in Vegas

With Shelby preparing to wind down production of its brutal GT350, a 624-horsepower Mustang that's meant to go up against the Roush Stage 3 in the world of tuned Ford ponycars, the Las Vegas-based tuner is looking to give back to one lucky customer. It'll auction off the very first GT350 ever produced, at the 2013 Barrett-Jackson auction in Las Vegas, a three-day event that runs from September 26 through September 28.
The GT350 is a monster, with a 5.0-liter, supercharged V8 that's been tuned well past 600 horsepower in a time when Ford's own Shelby-branded GT500 barely reached 550 horsepower. The GT350 is much louder than Ford's effort, too, both visually and audibly. The wide body look isn't what we'd call conventional, but on a car that sounds and goes like this, something extreme is needed. According to Shelby American's vice president of production, Gary Davis, "Carroll was very excited about the new wide body option, so that was included on this car. It's the first 2012 GT350 serial number from our anniversary year. It is a very special car." Wilwood brakes, a massaged suspension, and some very fat, sticky tires add to the Shelby experience.
This particular GT350 will be lot number 750, and will cross the Barrett-Jackson stage on Sunday, September 28.

The next-generation wearable will be your car

This year's CES has had a heavy emphasis on the class of device known as the "wearable" – think about the Apple Watch, or Fitbit, if that's helpful. These devices usually piggyback off of a smartphone's hardware or some other data connection and utilize various onboard sensors and feedback devices to interact with the wearer. In the case of the Fitbit, it's health tracking through sensors that monitor your pulse and movement; for the Apple Watch and similar devices, it's all that and some more. Manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality. As evidenced by Volvo's newly announced tie-up with the Microsoft Band 2 fitness tracking wearable, car manufacturers are starting to explore how wearable devices will help drivers. The On Call app brings voice commands, spoken into the Band 2, into the mix. It'll allow you to pass an address from your smartphone's agenda right to your Volvo's nav system, or to preheat your car. Eventually, Volvo would like your car to learn things about your routines, and communicate back to you – or even, improvise to help you wake up earlier to avoid that traffic that might make you late. Do you need to buy a device, like the $249 Band 2, and always wear it to have these sorts of interactions with your car? Despite the emphasis on wearables, CES 2016 has also given us a glimmer of a vehicle future that cuts out the wearable middleman entirely. Take Audi's new Fit Driver project. The goal is to reduce driver stress levels, prevent driver fatigue, and provide a relaxing interior environment by adjusting cabin elements like seat massage, climate control, and even the interior lighting. While it focuses on a wearable device to monitor heart rate and skin temperature, the Audi itself will use on-board sensors to examine driving style and breathing rate as well as external conditions – the weather, traffic, that sort of thing. Could the seats measure skin temperature? Could the seatbelt measure heart rate? Seems like Audi might not need the wearable at all – the car's already doing most of the work. Whether there's a device on a driver's wrist or not, manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality.