1980 Ford Ranger Base Standard Cab Pickup 2-door 2.8l on 2040-cars

Auto blog

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

2015 Hennessey Ford Mustang hits 207.9 mph

After hitting over 195 miles per hour a few months ago, John Hennessey was barely out of his personal HPE700 Mustang before he said that 200 mph was achievable. Don't doubt a man who knows a ton about taking cars to insane speeds. With the new HPE750 Mustang, he and his customers can finally surpass the 200-mph mark in their cars. "If at first you don't succeed, just add more horsepower and rpm and try again," Hennessey said in the company's announcement. Rather than the 717 horsepower and 632 pound-feet of torque from the supercharged 5.0-liter V8 in the HPE700, the HPE750 ratchets the same powertrain up to an even more potent 774 hp and 648 lb-ft. In a real show of confidence, the Hennessey team brought along Jay Leno when it returned to the Continental Tire Proving Grounds in Uvalde, TX, to set a new top speed with the HPE750. The upgrades to the Mustang definitely paid off because the pony car reached a GPS-verified 207.9 miles per hour down the straight. The run will eventually appear on a segment on the upcoming Jay Leno's Garage TV show that will air CNBC. Prices for the HPE750 start at $59,500 USD, including the base 2015 Mustang GT, but building an exact replica of this one would cost $69,374, according to Hennessey. In addition to the huge top speed, the company claims that the coupe can reach 60 mph in 3.4 seconds and cover the quarter mile in 10.9 seconds. 774 HP Hennessey Mustang Tested to 207.9 mph Jay Leno visits Texas tuner for upcoming TV series on CNBC June 2, 2015 Uvalde, Texas—On Wednesday, May 27, 2015, professional driver, Brian Smith, drove the Hennessey HPE750 Supercharged Mustang to a top speed of 207.9 mph. In the process, Hennessey's potent pony car became the first 2015 Mustang to break the 200 mph mark. Jay Leno was on hand to witness the record speed while filming an upcoming episode of Jay Leno's Garage, which will air on CNBC later this year. The run was made on the 8.5 mile high speed oval at the Continental Tire Proving Grounds located in Uvalde, Texas – the same test track where John Hennessey test drove the company's HPE700 Mustang to a top speed of 195 mph back in February of this year. During both tests, speeds were validated with Racelogic's VBox 3i GPS data logging system. "If at first you don't succeed, just add more horsepower and rpm and try again," said company founder and president, John Hennessey.

How Ford plans to handle insurance and repair questions surrounding new aluminum-bodied F-150

Building a car out of aluminum has a number of benefits - the lighter weight allows the vehicle to be more agile, more fuel efficient, make better use of its power and be more resistant to dings and dents. The downside to the advanced construction, though, is that repairs are both challenging and expensive. That's troubling for the new, aluminum-bodied Ford F-150, because it's kind of made a name for itself as a rugged, durable work vehicle.
How will the legions of Ford buyers cope when it comes time to insure and repair their new trucks? Well, according to Ford, it's expecting a ten-percent jump in insurance costs for the aluminum-bodied F-150, although Ford's truck marketing manager, Doug Scott, was quick to point out that the F-150 is generally cheaper to insure than its competition from Ram and General Motors. "At the end of the day, that's sort of a wash," Scott told Automotive News at last week's Detroit Auto Show. "We've spent a lot of time and feel very comfortable that that's not going to be an inhibitor."
The other issue facing Ford is the distinct lack of body shops that have the training or equipment to repair aluminum-bodied vehicles. AN cites an estimate from the Automotive Service Association claiming that of the 30,000 independent body shops in the US, less than 10 percent are able to work on aluminum.