2012 Ford Mustang Gt 5.0 Supercharged 13k Milies Tons Of Extras 605rwh on 2040-cars

Auto blog

Ford recalling 12,300 2015 F-150 pickups

Ford is recalling 12,300 of its new 2015 F-150 pickup trucks in North America. According to the automaker, an upper l-shaft may have been riveted improperly on these trucks, which can cause it to separate. If that happens, drivers may lose steering control without warning. Yikes. The affected trucks were built at Ford's Kansas City Assembly Plant between March 21 and 25, as well as the Dearborn Truck Plant between March 21 and 30. There are 12,328 total trucks included in this recall – 8,963 in the United States, 3,348 in Canada, and 17 in Mexico. Only 5,606 of the trucks are in customers' hands, the rest have yet to be sold. Ford is not aware of any accidents or injuries related to this problem, but knows of one incident where steering control was lost, and believes it to be related to this issue. Scroll down for Ford's official statement. Related Video: FORD ISSUES SAFETY RECALL FOR CERTAIN 2015 FORD F-150 VEHICLES IN NORTH AMERICA FOR UPPER I-SHAFT RIVET ISSUE Ford Motor Company is issuing a safety recall for approximately 12,300 2015-model Ford F-150 vehicles in North America for an upper I-shaft that might have been riveted improperly, potentially causing it to separate. If that happens, it could result in the loss of steering control without warning, increasing the risk of a crash. Ford is not aware of any accidents or injuries, but is aware of one report of loss of steering believed to be related to this condition. Affected vehicles include certain 2015 F-150 vehicles built at Kansas City Assembly Plant from March 19, 2015 to March 21, 2015 and certain 2015 F-150 vehicles built at Dearborn Truck Plant from March 21, 2015 to March 30, 2015. There are 12,328 vehicles that might be affected in North America, including 8,963 in the United States and federalized territories, 3,348 in Canada and 17 in Mexico. Of those, 6,722 vehicles are unsold, meaning 5,606 vehicles are in customer's hands. Dealers will inspect the upper I-shaft assembly and replace it if necessary at no cost to the customer.

2020 Ford Explorer, Lincoln Aviator reportedly facing numerous QC issues

A lengthy report in the Detroit Free Press delves into a range of quality control issues confronting the 2020 Ford Explorer and its luxury platform sibling, the 2020 Lincoln Aviator. Freep says it's been following the issue for two months, tapping various unnamed sources for information on the automaker's unorthodox route to resolution. Seems the problem is Explorers and Aviators leaving the production line at the Chicago Assembly Plant with flaws in areas like the chassis, transmission and suspension, said vehicles trucked to Ford's Flat Rock Assembly Plant (FRAP) outside of Detroit for repair. The estimates range from 10,000 to 18,000 vehicles affected, numbers so high that Ford has sought help from Roush Engineering in nearby Allen Park, and brought workers and managers from other plants in the Midwest to FRAP to get vehicles repaired and shipped to dealers. Ford hasn't shared the nature of the problems with anyone outside the company, including dealers and customers. Freep's sources are said to include workers who have provided photos of certain vehicles and of tents used to house parts at the FRAP repair site. The Explorer chassis allegedly has an unidentified problem that engineers are using X-rays to diagnose, and the transmission is having problems sensing when it's in park or going into park. Both the Explorer and Aviator have come off the line with HVAC units that only blow hot air. And the Aviator's height-adjustable suspension enters failure mode for unknown reasons. These come on top of quotidian mishaps common to every new vehicle, but that are meant to be sorted in pre-production, like missing emblems and trim pieces. They also come on top of a recall in early August issued for the Explorer and Aviator concerning the instrument cluster and parking brake, and another at the end of August over rear seatbacks that could collapse in a crash. An automaker spokesperson told Freep, "Making updates to preproduction models based on all-new platforms as they roll off the assembly line – is standard industry practice." Except these aren't pre-production, these are early production vehicles that paying customers and dealers are waiting for, and some of the affected vehicles have been pulled off dealer lots. Dealers say they are fine waiting for the trucks to get sorted out, and they'd rather have Ford fix the problems before the SUVs go to customers.

Toyo Tires will bring another wild catalog of rides to SEMA

Toyo Tires carts all kinds of toys to SEMA every year, the rubber company planning another 30 or so automotive exhibits this year in two locations. One of them, the Baja 911, comes with a pedigree not usually associated with the bewildering wares hawked at the Las Vegas show. TJ Russell was once lead fabricator for Singer Vehicle Design, now he's the head of Russell Built Fabrication in Sun Valley, CA. Sticking with the marque he knows well, Russell started with a 1991 Porsche Carrera 4 cabriolet, fitted the interior with a full roll cage, then built a hardtop around it to design a desert runner channeling the old Rothmans safari 911s. Underneath that bodywork lives a box-plate trailing arm suspension with 12 inches of travel, working 15-inch Fifteen52 FIA-approved Gravel wheels and 30-inch Toyo Open Country A/T II tires. Power comes from a purpose-built 3.8-liter air-cooled flat-six with about 350 horsepower — 100 hp more than stock — in a car that weighs 400 pounds less than the original. Oh, and as documented on Instagram with the tagline "All race outside, all business inside," the interior's full of quilted, cross-stitched leather, and Toyo says Russell's going to do a low-volume run of the Baja 911 starting early next year. ruffian-ford-mustang-sema-01 View 10 Photos Chris Ashton built a 1970 Ford Mustang Fastback called the Ruffian Mustang, inspired by the Trans Am Racing Series. The exterior changes are more subtle than one might think – the chin spoiler, hood scoop, and side mirrors are barely exaggerated versions of those on the original car, the intake vents astride the front lights and the steel bumpers teleported from 1970. Changes outside include de-chromed and flush-mounted glass, vented hood, front fenders that are dropped an inch, rear fender vents, dual side-exit pipes, and gargantuan fender flares over staggered Signature One wheels and Toyo Proxes 888 tires. The interior's fitted with a roll cage and race car workings. In spite of the Boss 427 badging, the engine's a 625-hp Chevrolet LS3 V8. button-built-ferrari-355-sema-01 View 13 Photos The Button Built Ferrari BB355TT picks up from last year's stanced BB328GTS widebody that gave many Internet denizens heart attacks. Laid up on a 1999 355 Berlinetta, the BB version appends a widebody kit designed Mitchell Button, rendered by Khyzyl Saleem and drenched in Azzuro la Plata, a color from Ferrari's Scagliette palette first used on a 1967 275GTB Le Mans racer.