2010 Ford Mustang Roush 427r on 2040-cars

Auto blog

Trump wants a trade deal, but South Korea doesn't want US cars

SEOUL - US auto imports from the likes of General Motors and Ford must become more chic, affordable or fuel-efficient to reap the rewards of President Donald Trump's attempts to renegotiate a trade deal with key ally South Korea, officials and industry experts in Seoul say. Meeting South Korean President Moon Jae-in last week in Washington, Trump said the United States would do more to address trade imbalances with South Korea and create "a fair shake" to sell more cars there, the world's 11th largest auto market. "What we really want to say to the United States is: Make good cars, make cars that Korean consumers like." While imports from automakers including Ford, Chrysler and GM more than doubled last year largely thanks to free trade deal which took effect in 2012, sales account for just 1 percent of a market dominated by more affordable models from local giants Hyundai and affiliate Kia. Imports make up just 15 percent of the overall Korean auto market, and are mainly more luxurious models from German automakers BMW and Daimler AG's Mercedes-Benz, which also benefit from a trade deal with the European Union. "Addressing non-tariff barriers would not fundamentally raise the competitiveness of US cars," a senior Korean government official told Reuters, declining to be identified because of the sensitivity of the subject. "What we really want to say to the United States is: Make good cars, make cars that Korean consumers like." TASTE BARRIER In Korea, US imports are seen as lagging German brands in brand image, sophistication and fuel economy, industry experts say. US imports do have a competitive advantage in electric cars: Tesla Motors' electric vehicles are seen as both environmentally friendly and trendy, while GM has launched a long-range Bolt EV. US Commerce Secretary Wilbur Ross had cited a quota in the current trade deal as an obstacle to boosting imports. The quota allows US automakers to bring in each year 25,000 vehicles that meet US, not necessarily Korean, safety standards. Should GM, for example, decide to bring in more than its quota of one model - the Impala sedans - it would cost up to $75 million to modify the cars to meet Korean safety standards, the company told its local labor union. Asked about non-tariff barriers, a spokesman at GM's Korean unit said removing them could expand the range of models the company can bring in from the United States. No US company, however, has yet to make full use of the quota, industry data shows.

The 1965 Ford Mustang could have looked a lot different

The 1965 Ford Mustang is unquestionably an automotive design icon, and nearly every generation of Mustang has some connection to that original car. Because it's such a universally-known vehicle, we were amazed to see all the different designs that were being considered. Head of Ford's archives Ted Ryan recently shared photos of design proposals for the original Mustang on Twitter that he and Jamie Myler found, and we reached out to them to find out more. As Ryan initially noted, the photos were taken on August 19, 1962, and they are proposals for the Ford Mustang. Apparently Ford had committed to doing a Falcon-based youth-oriented car at this point, and it did have plans to launch the car in 1964 for the 1965 model year. But after having little success with early design proposals, the company asked all of its design studios — the Advanced Studio, Lincoln-Mercury Studio and Ford Studio — to submit proposals. With only about two years before the planned launch, Ford was understandably short on time, and it's believed that the studios only had a month to create and present these designs. Lincoln-Mercury design proposal View 8 Photos The majority of the designs, a total of five, came from the Advanced Studio, and part of this was because they already had a couple of concept designs in reserve it could present. Two other models representing three design possibilities came from Lincoln-Mercury, and just one model with two options came from Ford. The Advanced Studio proposals are shown in the gallery at the very top of this article, and the Lincoln-Mercury and Ford proposals are in the gallery directly above this paragraph. The Advanced Studio's most radical design is the one that was clearly related to the Mustang I concept that would be shown later that year with huge wraparound rear glass, turbine-inspired bumpers and enormous side scoops. The other proposals from the studio were more conservative, featuring simple lines, grilles reminiscent of the Falcon, and one even borrowing the jet-thruster-style taillights made famous on the Thunderbird. Lincoln-Mercury had some impressively bold designs, particularly its fastback that had buttresses to extend the shape all the way to the tail. This car had two different side trim possibilities. The other Lincoln-Mercury design was toned down a bit, but had two interesting possibilities for side detailing, as well as some crisp, low-profile tail fins.

Ford investing $500M in engine plant for 2.7L EcoBoost production

Ohio is a hot area for Ford at the moment with the announcement just a few weeks ago that production of the next-generation F-650/F-750 medium-duty trucks would move from Mexico to the Ohio Assembly Plant in Avon Lake, Ohio. Now, Ford is investing $500 million to hire 300 workers at its Lima Engine Plant in Lima, Ohio, to add production of the twin-turbo 2.7-liter EcoBoost V6 for the 2015 F-150.
The latest investment will be used to add a new flexible engine assembly system and renovate 700,000 square feet of the plant for machining and assembly areas. The Lima factory already builds Ford's 3.5-liter and 3.7-liter Duratec V6 engines. The plant opened in 1957, and it's on track to build its 40 millionth engine later this year.
Ford claims that the 2.7-liter EcoBoost will offer V8 performance with better efficiency in the F-150. It comes standard with intelligent stop/start that doesn't activate when the truck is towing or in four-wheel drive, and it's made from a combination of compacted graphite iron and aluminum for low weight and high strength. The company says that V6 engines have already proven popular in the F-150 with 57 percent of trucks in 2014 being equipped with either the naturally aspirated 3.7-liter or turbocharged 3.5-liter EcoBoost engines.