1930 Model A Ford 5 Window Rumble Seat Coupe on 2040-cars

Auto blog

Major automakers urge Trump not to freeze fuel economy targets

WASHINGTON — Major automakers are telling the Trump administration they want to reach an agreement with California to avoid a legal battle over fuel efficiency standards, and they support continued increases in mileage standards through 2025. "We support standards that increase year over year that also are consistent with marketplace realities," Mitch Bainwol, chief executive of the Alliance of Automobile Manufacturers, a trade group representing major automakers, will tell a U.S. House of Representatives panel on Tuesday, according to written testimony released on Monday. The Trump administration is weighing how to revise fuel economy standards through at least the 2025 model year, and one option is to propose freezing the standards through 2026, effectively allowing automakers to delay investments in technology to cut greenhouse gas emissions from burning petroleum. The National Highway Traffic Safety Administration has not formally submitted its joint proposal with the Environmental Protection Agency to the White House Office of Management and Budget for review. Even so, last week, California and 16 other states sued to challenge the Trump administration's decision to revise U.S. vehicle rules. Auto industry executives have held meetings with the Trump administration for months and have urged the administration to try to reach a deal with California even as they support slowing the pace of reduction in carbon dioxide emissions that the Obama administration rules outlined. One automaker official said part of the message to President Donald Trump at a meeting on Friday will be to consider California like a foreign trade deal that needs to be renegotiated. Automakers want to urge him to get automakers a "better deal" — as opposed to potentially years of litigation between major states and federal regulators. On Friday, Trump is set to meet with the chief executives of General Motors, Ford, Fiat Chrysler and the top U.S. executives of at least five other major automakers, including Toyota, Volkswagen AG and Daimler AG, to talk about revisions to the vehicle rules. Senior EPA and Transportation Department officials will also attend. Environmental groups are eager to keep the rules in place, saying they will save consumers billions in fuel costs. A coalition of groups plans to stage a protest outside Ford's headquarters in Michigan.

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.