1929 Model A Tudor Sedan Ready For Restore Hotrod Ratrod on 2040-cars
Fayetteville, Arkansas, United States
Engine:Gas
Vehicle Title:Clear
Drive Type: Rear
Make: Ford
Mileage: 999,999
Model: Model A
Number of Cylinders: 4
Trim: Sedan
1929 Model A Tudor Sedan
I have for sale a 1929 Ford, Model A Tudor Sedan, almost complete, lots of new parts, ready to be finished and restored. I purchased this a few years ago, been purchasing parts here and there, in hopes that I would be able to put it together some day and enjoy it when it was complete. Due to health and tired of waiting, I decided to buy one that was complete and ready to drive. I absolutely love it and have decided to sell this one, along with all its parts, new and old. This project is literally ready to be put together. I have a lot of money tied up in this project and a lot of new parts. I have included a parts list below of all the new parts that will go with this project and have included as many pictures that eBay would allow. The vehicle comes with a clean Arkansas title!
The body is in good condition with surface rust throughout and typical cancer on front lower cowls, bottom doors and rear fender wells. I have new patches to fix the front lower cowl and rear fender wells (see parts list). Body is fairly straight with a few dings in places, but overall in great condition for its age. Body needs blasted, patches installed and paint. I have brand new metal fenders for the front (see parts list), but you will need to find fenders for the rear as well as the running boards. I purchased all new boards for the top/roof of vehicle along with new material to wrap it with (see parts list).
On the inside, I have all of the glass except for the passenger front door glass, it has the original floor boards, the driver side seat and the rear seat. The passenger side seat will need to be found and purchased. All seats need to be reupholstered. For some reason, I forgot to take picture of all the interior pieces, but they are included. I have the dash, all door panels and misc. trim.
The rolling chassis has been completely gone through and painted black. The rear axle has been rebuilt, front and rear hubs, as well as the transmission. Chassis is sitting on 19" wheels that could use a better paint job with fairly new tires. I will include an original set of 21" wheels, new with tubes and brand new BFG tires (see parts list).
You will receive 2 engines with this vehicle. One came off of the rolling chassis described above. Engine ran fine, but had some blow by and was removed to have rebuilt (still needs rebuilt). The second engine came with this Model A when I purchased it, was told that it ran, but never did hear it do so, but does turn over fine.
Parts list below are of all new parts that have been purchased and that are included with sale. Over $4000 in just new parts (2006 pricing, sells for more now), Chassis including rebuild over $3000, plus the price of actual car. Perfect for someone who is a collector or wants to put this together to flip.
-PAYMENT/SHIPPING -
You are bidding on this 1929 Model A Tudor Sedan. Whomever wins this auction will be responsible for picking this up. I may deliver to anyone in Arkansas or the surrounding areas for a fee, please contact me for possible arrangements.
I am asking for a $1000.00 deposit through PayPal at the time of listing end, and will accept the remainder in Cash or a Cashiers Check only at the time of pick up. If you win this auction, the payment is expected and arrangements need to be made within 5 days after sale ends. If you choose to back out or cancel this transaction, only 50%, or in this case $500.00 of the $1000.00 deposit will be refunded back to you. If you have any questions, please feel free to ask. Thanks for looking!
- 1929 FORD MODEL A TUDOR PARTS LIST -
Quantity: Description: Price: (2006 pricing)
( 5 ) ( 450-21 BFG Tires - Black - $101.91 ea ) ( $509.55 )
( 5 ) ( A-21 TR127 Nickel Stem Tubes - $24.95 ea ) ( $124.75 )
( 1 ) ( Front Fender A1605A - metal ) ( $449.95 )
( 1 ) ( Front Fender A16006A - metal ) ( $449.95 )
( 1 ) ( Hood Shelves A16713/14S - pair ) ( $32.50 )
( 1 ) ( Running Board Shields A16535-6B - set ) ( $154.50 )
( 1 ) ( Radiator Shell Plate A8200AC ) ( $139.95 )
( 1 ) ( Radiator Emblem A8212A ) ( $16.95 )
( 1 ) ( Front Lower Apron Between Fender A16527 ) ( $29.95 )
( 1 ) ( Headlights A13056AR - set ) ( $295.00 )
( 1 ) ( Wiring Harness A14403C ) ( $36.95 )
( 1 ) ( Ignition On Switch A11575F ) ( $21.95 )
( 1 ) ( Nuts A14561W - box ) ( $2.00 )
( 1 ) ( Terminal Box Lid A14561A ) ( $3.95 )
( 4 ) ( Spark Plugs - $4.95 ea ) ( $19.80 )
( 1 ) ( Ignition Points Set - .018 .022 A12199 ) ( $9.95 )
( 1 ) ( Condenser A12300 ) ( $3.95 )
( 1 ) ( Rotor A12200 ) ( $3.95 )
( 1 ) ( Spark Plug Connectors - set of 4 ) ( $1.95 )
(7 yd ) ( Roof Material - $4.95 per yard ) ( $34.65 )
(24 yd) ( Top Cloth Medium Welt - $0.50 per yard ) ( $12.00 )
( 1 ) ( A 1035-1 Header Wood ) ( $66.50 )
( 1 ) ( Bolts - Fender ) ( $14.50 )
( 2 ) ( Window Cranks - $8.95 ea ) ( $17.90 )
( 1 ) ( Front Floor Mat ) ( $39.95 )
( 1 ) ( Rear Floor Mat ) ( $59.95 )
( 5 ) ( Hub Caps ) ( $49.75 )
( n/a ) ( 4.972 yds 1-5 Fancy Upholstery ) ( $23.87 )
( n/a ) ( 3.694 yds 1-5 Fancy Upholstery ) ( $17.73 )
( n/a ) ( Chassis/ Window Channel ) ( $42.95 )
( n/a ) ( Cradle/Starter Crank ) ( $9.95 )
( 2 ) ( 28-31 Running Board Bracket anti Squeak Welt - rolls ) ( $5.50 )
( 1 ) ( 28-29 Radiator to Shell Mounting Set - 12 pc - set ) ( $1.25 )
( 1 ) ( 28-30 Radiator Emblem/Script/Blue on Chrome ) ( $38.50 )
( 1 ) ( 28-29 Crank Hole Cover w/ Rivet/stainless steel ) ( $2.90 )
( 5 ) ( Rim Liners 17" - 21"/ 26-48 ) ( $14.75 )
( 1 ) ( Instrument Panel Screw Set - 28-Mid30 - set ) ( $1.00 )
( 1 ) ( Body to Frame Welt w/adhesive backing 1/8"x2"x20' - roll ) ( $24.95 )
( 1 ) ( 28-28 Radiator Mounting Kit/original style - kit ) ( $3.95 )
( 2 ) ( 28-29 Hood Retainer- $6.20 ea (cancelled 1 Hood Retainer) ) ( $12.40 )
( 2 ) ( 28-31 Tudor, Fordor, Phaeton Rear Fender Brace ) ( $35.00 )
( 2 ) ( 16" Fender Welting ) ( $16.00 )
( 1 ) ( 28-29 Hood Hinge Rods in Stainless ) ( $12.75 )
( 1 ) ( Hood Corner Pads ) ( $3.50 )
( 1 ) ( Hood Prop Kit ) ( $28.05 )
( 1 ) ( Hood Retainer SS scs 28-29 ) ( $3.00 )
( 2 ) ( 28-29 Hood Retainer Shim ) ( $1.40 )
( 1 ) ( 28-29 Hood Cowl Lacing Hook ) ( $1.95 )
( 4 ) ( 28-29 Hood Latch - $8.00 ea ) ( $32.00 )
( 1 ) ( Hood Latch SCS 28-29 ) ( $2.60 )
( 1 ) ( Hood Latch Pads ) ( $1.75 )
( 1 ) ( Hood Latch Bumpers ) ( $4.95 )
( 1 ) ( 28-29 Tudor Sedan Body to Frame Bolt Set ) ( $6.75 )
( 1 ) ( 28-29 Tudor Sedan Top Wood & Screw Kit ) ( $30.50 )
( 1 ) ( 28-29 Tudor Sedan Top Wood Kit ) ( $432.00 )
( 1 ) ( Rear Inner Fender Patch Panels - set (LH & RH) - 2 HUMP/28-31 ) ( $55.25 )
( 1 ) ( Cowl Quarter Patch Panels - set (LH & RH) - 28-29 ) ( $40.75 )
( 1 ) ( 28-29 Body Mounting Wood Block Set /7 pc/ Tudor - set ) ( $42.25 )
( 2 ) ( 28-31 Front Running Board Brackets 17" ) ( $55.00 )
( 1 ) ( 28-31 Running Board Bracket / Left Rear ) ( $27.50 )
( 1 ) ( 28-31 Running Board Bracket/ Right Rear ) ( $27.50 )
( 1 ) ( 28-31 Running Board Bracket Bolt Set/ 36 pc - set ) ( $4.25 )
( 1 ) ( 28-31 Gas Gauge ) ( $34.95 )
( 4 ) ( 28-31 Window Riser Escutcheons ) ( $19.80 )
( 1 ) ( 28-31 Slide Lock Knob ) ( $3.95 )
( 1 ) ( 28-29 Locking Door Handle ) ( $31.95 )
( 1 ) ( 28-31 Stainless Steel Conduit (3) - set ) ( $10.95 )
( 1 ) ( 28-29 Non Locking door Handle ) ( $31.95 )
( 1 ) ( 28-31 Gas Tank Filter ) ( $6.50 )
( 1 ) ( 26-32 Pivot Bolt Set - 2 ) ( $4.25 )
( 1 ) ( 28-31 Inside Sliding Lock Escutcheon ) ( $4.95 )
( 1 ) ( 28-31 Sliding Door Lock Screws - set - 2 ) ( $1.25 )
( 1 ) ( 26-31 Stainless Steel Windshield Swing Arms - set - 2 ) ( $18.91 )
( 1 ) ( 28-31 Inside Sliding Lock ) ( $5.00 )
( 1 ) ( 28-31 Terminal Box ) ( $12.95 )
( 1 ) ( 28-31 Inside Gas Shutoff USA ) ( $39.95 )
( 2 ) ( 26-32 Slide Nuts ) ( $11.00 )
( 2 ) ( Inside Door Handle Escutcheons ) ( $11.90 )
( 1 ) ( Swing Arm Washers - set ) ( $6.95 )
( 1 ) ( 28-31 Patent Plate ) ( $3.75 )
( 1 ) ( 28-34 Door Handle Pads - set ) ( $3.00 )
( 1 ) ( A13708AC 28-29 Model A Dash Lamp Assembly ) ( $24.95 )
( 1 ) ( 28-31 15-30-15 Amp Meter ) ( $10.95 )
( 2 ) ( 26-31 Window Riser Handles ) ( $23.90 )
( 2 ) ( 26-31 Window Riser Handles ) ( $21.90 )
( 1 ) ( 28-29 Center Bumper Medallion ) ( $12.95 )
( 1 ) ( 28-31 On-Off Plate w/ SS Ring ) ( $5.50 )
( 1 ) ( 28-31 Backplate ) ( $1.75 )
( 2 ) ( Inside Door Handles ) ( $19.90 )
( 4 ) ( Door and Window Springs ) ( $2.36 )
( 2 ) ( Inside Door Handle Screws ) ( $0.90 )
( 1 ) ( Shell Lacing St/ w-rivets/ 28-29 - set ) ( $6.75 )
( 1 ) ( 28-29 Grommet set/ Radiator Shell/ Rubber/ 3 pc - set ) ( $1.75 )
Ford Model A for Sale
Auto Services in Arkansas
Young Tire & Auto ★★★★★
Wholesale Auto Company ★★★★★
Whittle Truck Sales & Trailer Rental ★★★★★
Warp Speed Performance ★★★★★
Superior Nissan ★★★★★
Pep Boys Auto Parts & Service ★★★★★
Auto blog
70% of pickups could use aluminum by 2025
Wed, 11 Jun 2014In the next decade, the auto industry will see an explosion in its use of aluminum to cut weight and increase fuel economy, according to a study from market analysts Ducker Worldwide cited by The Detroit News. We are already seeing the lightweight metal show up extensively in luxury models from Europe, but with the impending launch of aluminum-intensive 2015 Ford F-150 (pictured above), North America is using it even more, as well. The report predicts 70 percent of US pickups to have aluminum bodies by 2025.
It won't just be pickups that see the benefit, though. The average amount of aluminum in US vehicles is forecasted by the study to grow from an average of 350 pounds in 2013 to about 550 pounds by 2025. The most common parts to use it will be hoods, doors and - to some extent - roofs, as well.
The massive increase in pickups' aluminum content hardly seems surprising. The F-150 is predicted to use so much that it might cause a short-term shortage, according to one earlier report. At the same time General Motors is heavily rumored to be negotiating with suppliers for the next generation Chevrolet Silverado and GMC Sierra. Ram is the last holdout of the Big Three, but the study predicts that not to last.
Production Ford Escort heading for Beijing
Wed, 16 Apr 2014Ford's long-dormant Escort nameplate returned affixed to a sedan concept at last year's Shanghai Motor Show. While not exactly a beauty, it showed a clean, straightforward take on Ford's current styling. The Blue Oval said at the time that it wanted to create a model that was stylish "but not one that is arrogant or pretentious." Job done. A year later, it looks like the minimalist vehicle might make its production debut at the Beijing Motor Show.
Autocar claims that the streetgoing version has been confirmed to it for the upcoming show, but so far, Ford isn't saying. If unveiled, the Escort is likely to be produced locally for the Chinese market with a domestic partner. Powertrain details remain a secret, but it seems highly likely that any production model would use a small three- or four-cylinder engine and front-wheel drive. Sales in other major world markets like ours are unlikely, but a test car was recently spotted in Europe.
Autoblog contacted Ford for confirmation, but the automaker demurred, with a spokesperson saying only, "At the moment, we are not confirming any vehicles planned for the show." It looks like we will have to wait to know for sure.
2015 Hennessey VelociRaptor 600 fills an F-150 Raptor-sized void
Tue, Dec 16 2014Ford is rumored to possibly debut a new F-150 Raptor at the upcoming Detroit Auto Show in January, but whether that's the case or not, Hennessey Performance is ready to fill the muscle truck niche now with its latest VelociRaptor 600 Supercharged based on the 2015 F-150. The fantastically named VelociRaptor package has been available on the regular Raptor for the past few years, taking power up to 600 horsepower or more, depending on what the buyer desired. With the latest one, the performance truck is now based on the aluminum-bodied F-150, specifically the FX4 Super Crew model with the 5.0-liter V8. "Having Ford's world-class new truck design, with a weight savings of nearly 700 pounds, our VelociRaptor 600 Supercharged will have an even greater level of performance and driving excitement," said founder John Hennessey in the company's release. The heart of VelociRaptor is the Roots-type supercharger running at 8 psi on the V8. With help from upgraded fuel injectors, a proprietary engine management system and stainless steel exhaust, it boosts grunt from a stock 385 horsepower to over 600 hp. To make sure that power gets to the road, the package also includes 33-inch BFGoodrich mounted on 17-inch Hennessey wheels. For buyers in need of more, the company offers optional parts including an off-road coilover suspension, different front and rear bumpers, a winch, LED light bar and Brembo brakes. Speaking to Autoblog, Hennessey said he feels confident that the latest VelociRaptor could do high-four-second sprints to 60 miles per hour, compared to the outgoing model in the low-five-second range. Prices for the VelociRaptor start at $73,500, which includes the donor F-150, and orders are open now. Actual deliveries should start by March at the latest, according to Hennessey. The company also plans to offer a similar package for EcoBoost F-150s later. Scroll down to read the full announcement about this muscle truck. Introducing the 2015 Hennessey VelociRaptor 600 Supercharged Texas tuner adds power and improved off-road capabilities to Ford's all-new aluminum bodied pick-up trucks December 16, 2014-For immediate release Sealy, Texas-For the past five years, Ford F-150 truck enthusiasts have had the special opportunity to own the SVT Raptor. With 411 hp and baja pre-runner capabilities, the Ford Raptor was one of the most capable 4x4's ever built. Sadly, Ford Raptor production has ended, leaving a void in the market for 2015.